1.1Battery pack replaces ecvp
A battery pack supplies direct current to an electric motor. The motor drives the transmission output shaft. The controller adjusts motor torque based on draft force feedback.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about individual parts of claim 1: what if that part was like this, and not that.
A battery pack supplies direct current to an electric motor. The motor drives the transmission output shaft. The controller adjusts motor torque based on draft force feedback.
A mechanical transmission uses gears and clutches to change speed ratios. The engine drives the input shaft. The output shaft delivers mechanical power to the wheels.
Continuous tracks distribute vehicle weight over a larger surface area. Drive sprockets rotate the tracks. The tracks propel the vehicle across soft terrain.
An analog comparator compares two voltage signals. The output switches state based on which input is higher. The output signal drives a hydraulic valve.
The output signal energizes a solenoid valve. Hydraulic fluid flows to a cylinder. The cylinder extends or retracts to adjust implement height.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
The arrangement is applied to a marine propulsion system where a ground engaging member is replaced by a marine propeller. The electric continuously variable power sources drive the propeller shaft through a split-path transmission. The processor monitors the motor current to estimate propeller thrust and adjusts the propeller pitch to maintain a desired thrust level.
The arrangement is applied to a construction excavator where the ground engaging member is a digging bucket. The electric continuously variable power sources drive the hydraulic pumps that operate the boom and arm. The processor monitors the motor current to estimate bucket resistance and adjusts the boom cylinder pressure to maintain a desired digging force.
A rotary torque sensor is installed on the transmission output shaft to measure mechanical torque directly. The processor receives the torque signal instead of relying solely on motor voltage or current. The control logic compares the measured torque to a setpoint and commands the implement lift valve to adjust the draft force.
The electric continuously variable power sources operate at 800 volts direct current to reduce current flow and minimize cable weight. The processor samples the voltage and current signals at a rate of 10 kilohertz. The control loop adjusts the implement depth every 50 milliseconds to maintain the desired draft force.
The draft control system is integrated with a global navigation satellite system receiver mounted on the vehicle roof. The processor uses satellite position data to calculate vehicle speed and travel distance. The control logic adjusts the draft force setpoint based on the vehicle speed to maintain consistent soil engagement.
A trained neural network model processes historical motor current, vehicle speed, and soil moisture data. The model predicts the required draft force for upcoming terrain conditions. The processor generates the output signal to adjust the implement depth proactively based on the predicted draft force.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
For example, power supply 14 may include a prime mover 20 and an electric generator 22.A · US 8,310,176 B2 · ¶ 24
As best shown in FIGS. 1 and 2, a power line 25 may electrically connect power regulator 24 of power supply 14 to drive group 16.A · US 8,310,176 B2 · ¶ 27
From power line 25, the electricity may flow through each of traction motors TM1-TM6, which may use the electricity to drive traction devices TD1-TD6.A · US 8,310,176 B2 · ¶ 35
Accordingly, a draft control device is provided to the tractor so as to maintain a uniform traction load in active response to the traction load which changes during the plow work.B · US 10,039,224 B2 · ¶ 8
Therefore, during forward driving in a state, in which the plow is attached to the three-point hitch, when plow resistance is generated in the opposite direction of the driving direction, the compressive force transmitted to the top link is transmitted to the top link swing bracket 42 as it is, wherein the top link swing bracket 42 is rotated by the force with respect to the hinge point by the connection pin 41 in a direction, in which the top link swing bracket 42 comes towaB · US 10,039,224 B2 · ¶ 46
An empty cell means only that no passage was reproduced there.
One strategy for correcting wheel slip is to simply decrease the electrical power supplied to the traction motors.A · US 8,310,176 B2 · ¶ 8
However, due to operating characteristics typical of systems that supply electricity to the traction motors, the amount of electrical power supplied to the traction motors may decrease more slowly than desired.A · US 8,310,176 B2 · ¶ 8
In the case where plow work is to be carried out using a plow among the work machines attached to the rear side of a tractor, there is difficulty of varying degrees depending on the soil condition in maintaining desired plowing depth due to the characteristics of the plow since a plow blade is likely to grow in the soil during the plow work.B · US 10,039,224 B2 · ¶ 7
This draft control device helps the smooth plow work without overload by automatically lifting the three-point hitch, when the plowing depth of the work machine, which is connected to the three-point hitch at the rear side of the tractor, becomes excessively deep, resulting in the overload.B · US 10,039,224 B2 · ¶ 8
patent.fyi, US 12,796,582 B2, claim 1, first published 2026-11-18T13:13:23-05:00, https://patent.fyi/US12796582/, SHA-256 ea2395b30a35d9e762c4eb660363024c29bb6003a1a9c549366e128d94ff69f8