1.1Rotary scoop soil pickup
Curved scoops on the drum enter the soil from above and lift a shallow layer as the drum turns. A fixed scraper strips the lifted material from the scoops onto the conveyor receiving end.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Curved scoops on the drum enter the soil from above and lift a shallow layer as the drum turns. A fixed scraper strips the lifted material from the scoops onto the conveyor receiving end.
Powered rubber feed rolls at the share exit lift the cut layer along a short solid ramp to the horizontal screen. Soil drops through the screen, and retained stones fall from its rear end into a crusher mounted below deck level.
A metering roller spreads the feed in a shallow layer on the solid belt. An overhead suction hood draws fine soil into a cyclone, which releases it through a rotary airlock, while the belt carries the heavier stones to the crusher.
The screen returns loose soil to the ground and carries retained stones to the hopper. A hydraulic cylinder tips the hopper into a collection trailer when the hopper reaches its fill level.
The screen conveyor drops retained stones through a fixed chute to form a narrow windrow. On a second pass, a spring tine drum lifts stones from the windrow and releases them into the crusher inlet.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A transverse share on a beach grooming machine lifts a shallow layer of dry sand and shell fragments onto an inclined screen conveyor. Sand falls through the screen and returns to the beach beneath the machine. Retained shell fragments fall from the upper end of the conveyor into a toothed roll crusher. A chute beneath the crusher directs the crushed shell into a collection bin.
A rotating disc separator replaces the screen conveyor and rises rearward from the transverse share to a chute above the crusher inlet. The deck consists of parallel transverse shafts fitted with staggered discs that rotate together to move material uphill. Soil falls through the gaps between the discs as the discs break apart loose clods. Stones that bridge the gaps travel to the upper end and fall through the chute into the crusher.
A transverse pickup rotor fitted with replaceable curved steel tines takes the place of the fixed share. Gauge wheels set the tine penetration, and a hydraulic drive turns the rotor so the tines sweep rearward through the soil at the bottom of their travel. A curved hood guides the lifted mixture onto the lower end of the inclined screen conveyor. Soil drops through the screen, while retained stones travel to the crusher inlet.
A compact carrier supports a 0.75 m transverse share, with gauge wheels set to hold a 60 mm working depth. A 0.80 m wide screen conveyor begins immediately behind the share and rises at 20 degrees, with 25 mm clear openings between its rods. The carrier travels at 0.4 m/s while the screen moves uphill at 0.8 m/s. Soil falls through the screen, and retained stones feed into a compact jaw crusher that discharges through a chute beneath the rear of the carrier.
A seed drill attaches behind the mobile share, screen conveyor and crusher assembly. Soil falls through the screen, and a transverse chute spreads crushed stone over the same strip ahead of a spring tine harrow. The harrow mixes the fragments into the surface and levels the strip ahead of the drill openers. A ground wheel drives the seed meters in proportion to travel speed, and press wheels close the seed furrows.
A pressure transducer measures the differential pressure across the hydraulic motor that drives the crusher, and a shaft sensor measures crusher speed. A controller trims the speed of the hydrostatic travel drive when sustained crusher pressure exceeds a setpoint, reducing the rate at which the share feeds material onto the inclined screen. If the crusher speed falls below a set minimum, the controller stops travel and stops the screen conveyor. When crusher speed recovers and pressure drops below a lower setpoint, the controller restarts the conveyor before ramping up travel.
The mixed feed slides down a steep chute onto a bank of closely spaced rollers. Loose soil falls between the rollers, and the rotating rollers move retained stones onto the solid belt for delivery to the crusher.
A transverse steel share carries a bolted abrasion resistant cutting edge across the working width. Gauge wheels set the edge 60 mm below the ground surface, and the inclined share face lifts the cut layer toward the screen.
Two side chains carry transverse steel rods at a 20 degree upward angle toward the rear of the machine. The rods have 18 mm clear gaps that pass loose soil under gravity and carry stones too large to fit through the gaps.
Hinged steel plates form an endless apron that rises rearward from a receiving end immediately behind the share. Round 22 mm apertures pass loose soil under gravity, and low transverse cleats carry retained stones to the discharge.
A steel feed chute directs stones from the conveyor discharge into a jaw crusher with one fixed jaw and one moving jaw. An eccentric shaft drives the moving jaw, and crushed material falls through the bottom opening when the fragments fit through the gap.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
(f) a first digging blade pivotally attached to the first hinge and a second digging blade pivotally attached to the second hinge; wherein the first digging blade and second digging blade both surround the base and are oriented to face each other; wherein digging blades can together pivot inwardly towards each other to an engaged position or together pivot outwardly away from each other to a disengaged position;A · US 7,784,842 B1 · claim 1
Constructions are known in which the screening unit forms a simple conveyor trough which is provided with openings in order to achieve a screening action (grate-type trough).B · US 11,369,972 B2 · ¶ 2
A material crusher apparatus, comprising: a hopper for receiving material to be crushed; a screen configured to receive the material from the hopper and to separate the material into a first portion and a second portion; a vibration generator configured to vibrate the screen; a crusher configured to receive the first portion of material from the screen; a crusher discharge conveyor configured to receive crushed material from the crusher; a take-off conveyor; and an adjustableB · US 11,369,972 B2 · claim 1
An empty cell means only that no passage was reproduced there.
Digging holes in soil or other materials can be particularly strenuous and time consuming.A · US 7,784,842 B1 · ¶ 2
The device can help a user dig a hole more easily and more efficiently.A · US 7,784,842 B1 · ¶ 2
During operation, it frequently occurs that the screened-out fine partial fraction sticks to the surface of the flap and increasingly blocks it.B · US 11,369,972 B2 · ¶ 3
Consequently, during operation, the flap vibrates together with the screening unit, so that the fine screenings are prevented from sticking to the surface of the flap.B · US 11,369,972 B2 · ¶ 6
patent.fyi, US 2026/0354295 A1, claim 1, first published 2026-11-18T21:18:11-05:00, https://patent.fyi/US20260354295/, SHA-256 2d7543e80aa14475dd5f53acf6ae97d13d6c60ab9fa8865aba7b8166f76c5bb1