1.2Flat gasket between flanges
A rectangular strip of nitrile rubber lies between the flange faces on the cylinder side of the screw row. Tightening the screws compresses the strip against both faces along the full seam.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A rectangular strip of nitrile rubber lies between the flange faces on the cylinder side of the screw row. Tightening the screws compresses the strip against both faces along the full seam.
A continuous bead of room-temperature-curing silicone runs along one flat flange face. Assembly spreads the bead into a thin layer that fills surface irregularities and cures into a continuous barrier.
The shell edges terminate at the same seam plane and turn outward to form opposing flanges. Screws through the flanges compress a full-length solid rubber strip, and neither shell edge extends across the seam.
The halves swing open on hinges fixed to the cylinder end flange. Over-center latches draw the halves against a gasket at the end flange and compress a second gasket along the split.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A horizontal drum meters screened wood chips from a hopper onto a belt conveyor at a wood processing plant. Three curved steel plates bolt together along longitudinal seams with an O-ring in a channel, a band against a 45-degree chamfer, and a stamped overlap, one at each seam. Circular covers close both ends, and paired slides close the shaft opening in each cover. The drum turns beneath the hopper, and shallow external pockets carry chips to the discharge while the seams and end closures keep fines out of the hollow drum.
A die-cut closed-cell nitrile rubber gasket replaces the channel and O-ring at one longitudinal seam. Flat inward-facing flanges on the adjacent curved plates provide continuous seating faces, with the fastener row inboard of the gasket. Metal compression stops set the closed flange gap to 2.25 mm for a 3 mm gasket. The gasket extends to the end cover seating faces, where it meets the end seals.
Each circular cover has two semicircular halves that bolt around a shaft collar welded to the shaft. A split nitrile compression ring replaces the slides, with its inner lip seated on the collar and its outer flange captured in a counterbore in the cover. The ring joints sit 90 degrees from the cover split, and flat gasket strips seal the mating faces of the cover halves. Bolts draw the halves together around the ring, and a perimeter gasket seals the cover against the drum rim.
Four 90-degree curved steel plates form a drum with a 400 mm outside diameter and a 600 mm working length. Inward-facing flanges run along the four longitudinal seams and carry M6 fasteners at 75 mm centers. Opposing seams use channel O-rings, and the other two use bands compressed against 45-degree chamfers. Circular end covers register on machined seats at both ends, and paired slides close each shaft opening after the covers are fitted.
A sheet metal hood encloses the transfer gap between the sealed feeder drum and a discharge belt. A branch duct connects the top of the hood to a cyclone separator and an induced-draft fan, with a balancing damper in the branch. A downward-facing baffle shields the duct inlet from falling crop material while the fan draws suspended dust upward. The drum retains its longitudinal seam seals and paired end slides, and a rotary airlock discharges collected dust from the cyclone into a bin.
Each end slide carries a steel target, and each circular cover holds an inductive proximity switch aligned with the target at the fully seated position. The switches connect to a drum-mounted controller supplied through a shaft-end slip ring that also carries the controller output. The drive controller permits startup when every switch reports closure continuously for 500 milliseconds. During operation, loss of any closure signal for more than 100 milliseconds commands a controlled stop and identifies the affected slide on the operator display.
Complementary hooks formed into adjoining plate edges engage by sliding the plates lengthwise. The interlocked profiles resist radial separation, and the end covers capture the plate ends to limit axial movement.
M8 flange-head screws pass through clearance holes in the outward-facing seam flanges and engage captive nuts on the opposing flanges. The captive nuts let a technician remove each screw from the accessible side of the seam.
A rectangular channel in one mating flange holds a continuous nitrile O-ring with a 4 mm cross-section. A 3.2 mm channel depth gives 20 percent nominal squeeze when the opposing flange contacts the channel shoulders.
Two semicircular cover halves at each end travel inward on straight slide rails captured in opposed guide channels. Tapered blocks at the ends of the guides press the halves axially against a face gasket as they reach the closed position.
patent.fyi, US 2026/0354309 A1, claim 1, first published 2026-11-18T21:18:11-05:00, https://patent.fyi/US20260354309/, SHA-256 cfc26b24fc1f12e8fe4e077cc707134d32c4eb5122197d1fe9cf83e806988729