1.1Fixed fins of different pitches
Each removable carrier holds fins welded at a preset pitch to the rotor axis. Bolts secure the selected carrier to the concave frame, and the fin pitch sets the axial component of crop deflection.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each removable carrier holds fins welded at a preset pitch to the rotor axis. Bolts secure the selected carrier to the concave frame, and the fin pitch sets the axial component of crop deflection.
Brackets on the housing support the fin pivots and hold the fins above the crop path. The concave portions move on separate links to set rotor clearance.
Two spaced shoes on each fin travel in concentric arcuate slots centered on a common virtual pivot. A linear actuator moves a fin lug along the arc, and the slot walls carry the crop reaction loads.
A stub shaft passes through a reinforced boss near the middle of the fin and turns in two spaced bushings in a support bracket. An actuator link turns a crank on the shaft to set the fin pitch.
A wear pad on each opposed edge bears against a curved guide on a crossmember above the concave. As each fin turns about its driven pivot, the pad slides along the guide and transfers crop loads to the crossmember.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stationary dry bean sheller uses a rotor above a perforated concave that passes shelled beans into a collection hopper. Adjustable fins above the concave pivot on shafts carried by lengthwise support bars, with their opposed edges hinged to the upper concave edge. An external hand lever moves a tie rod connected to cranks on the fin shafts. The fins direct opened pods toward the discharge chute while beans fall through the concave.
A curved slot and roller replace the hinge at the opposed edge of each fin. The fin retains its pivot shaft on the lengthwise support bar, and a pin on the opposed edge carries a roller captured in a guide plate bolted to the upper concave edge. The curved slot follows an arc centered on the pivot shaft. The roller follows the slot as an external actuator rotates the shaft and transfers load from the fin edge to the concave frame.
Spring stainless steel strips replace the pin hinges along the opposed upper edge of the concave. Two strips per fin bridge the joint, with one end of each strip clamped to the fin and the other end clamped to a bracket on the concave. The strips bend as the external actuator turns the fin about its shaft on the lengthwise support bar. Mechanical stops limit rotation to the elastic travel of the strips.
A 600 mm concave carries four fins at 150 mm axial pitch, with the first pivot centered 75 mm from the inlet end. The pivot shafts sit on lengthwise support bars, and opposed fin edges hinge at the upper concave edge. A single external tie rod moves all four fins together through a 30 degree rotation. Adjustable stop bolts on the tie rod bracket set the endpoints of travel.
A quick change concave carrier supports removable sections, each carrying its own fin shafts, lengthwise support bars, and opposed edge hinges. Each section has a bellcrank that connects to the external actuator rod through a captive clevis pin. Pulling the pin releases the rod so the section and its fins slide out together. The replacement section seats against locating stops before the rod reconnects to its bellcrank.
A torque sensor on the rotor drive and a rotary encoder on a fin shaft report to a controller. The controller samples torque at 20 Hz and computes a moving average over one second. When the average exceeds an operator-set upper limit, an external actuator turns the hinged fins two degrees toward faster discharge, then holds the new angle for three seconds. When torque stays below a separate lower limit for five seconds, the actuator returns the fins toward the operator's preset angle in two degree steps.
Successive paddles sit at axial and circumferential offsets along the rotor. Their pitched faces drive the crop mat toward the discharge as the rotor turns.
A double-acting hydraulic cylinder mounted outside the concave turns a bell crank linked to a common tie rod. The tie rod moves crank arms on the fin shafts together, and adjustable stops limit their angular travel.
Steel rail segments bolt lengthwise above the concave portions and carry aligned shaft bores. Replaceable flanged bushings pressed into the bores support the fin hinge shafts.
Rolled steel knuckles on the fin edge interleave with knuckles on a support plate. A hardened steel pin passes through the knuckles, and retaining rings hold the pin axially.
Clevis brackets bolt to the opposed upper edge of the concave portions and receive tabs on the opposed fin edges. Shoulder pins pass through the clevis ears and bushed tabs to carry fin loads while permitting rotation.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
FIG. 3 sets forth a diagram of a blower (302) with adjustable guide vanes (312) that are affixed to the blower (302) at pivot points (318) located in an outlet (306) of the blower (302).A · US 8,591,167 B2 · ¶ 23
Each of the lower secondary vanes 704 includes a lower secondary vane pivot shaft 708 which extends vertically upward through lower primary vane portion 604. The upper secondary vane pivot shaft 706 and lower secondary vane pivot shaft 708 are fixedly connected to each other and are freely rotatable about a vertical axis 710 that extends through the primary vane 600.B · US 11,299,015 B2 · ¶ 50
An empty cell means only that no passage was reproduced there.
Such blowers, however, often deliver cool air through an outlet of the blower in a manner that is not uniform.A · US 8,591,167 B2 · ¶ 5
Methods, apparatus, and products are disclosed for improving airflow from a blower with one or more adjustable guide vanes that are affixed to the blower at one or more pivot points located in an outlet of the blower that include determining a rotational speed of an impeller in the blower and adjusting a position of at least one of the adjustable guide vanes in dependence upon the rotational speed of the impeller.A · US 8,591,167 B2 · ¶ 6
In an exemplary aspect, a vehicle air vent includes a primary vane system pivotal about a horizontal axis to direct an airflow from an outlet of the vehicle air vent in an up/down direction, a secondary vane system pivotal about a vertical axis to direct an airflow from an outlet of the vehicle air vent in a side-to-side direction.B · US 11,299,015 B2 · ¶ 4
The vehicle air vent further includes an airflow volume control system adapted to adjust the volume of airflow through the vehicle air vent, and a joystick controller adapted to independently operate the primary vane system, the secondary vane system, and the airflow volume control system.B · US 11,299,015 B2 · ¶ 4
patent.fyi, US 2026/0354310 A1, claim 1, first published 2026-11-18T21:18:11-05:00, https://patent.fyi/US20260354310/, SHA-256 deb18c89bdeef68ba6bc0b8aa61176b71343a4db7dffaab2646f97eb42a5a517