1.2Side inlet with forward outlet
A screened side opening feeds a curved duct that turns the incoming air 90 degrees toward an axial fan. The fan drives air through a forward nozzle that concentrates the discharge.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A screened side opening feeds a curved duct that turns the incoming air 90 degrees toward an axial fan. The fan drives air through a forward nozzle that concentrates the discharge.
Air enters the eye of a centrifugal impeller along the motor shaft and exits the blade passages radially. A scroll collects the discharged air and directs it into the forward duct.
A circumferential row of screened openings feeds an annular plenum around the motor. A curved partition routes air upstream within the plenum and then turns it forward into the fan face.
A frustoconical wall reduces the duct diameter from 120 millimeters at the inlet to 85 millimeters at the throat. The shrinking flow area accelerates air before it enters the fan.
A molded intake wall contracts along a smooth curve from the inlet lip to the fan face. The final wall diameter sets the running clearance around the blade tips at the fan entrance.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handheld housing contains a bell-shaped inlet, a cylindrical intake section and an axial fan in that order. A removable nozzle couples to the outlet and tapers to a rectangular slot that forms a sheet of air. The operator sweeps the slot across a rinsed part with the jet angled toward a drain tray to push water out of recesses.
Injection-molded nylon with 30 percent short glass fiber replaces aluminum in the intake duct. The molded part forms the bell-shaped inlet and downstream cylindrical section as one piece with external mounting ribs. An annular pilot on the downstream flange centers the intake on a separate fan carrier, and an elastomer gasket seals the joint.
The intake has a maximum bell radius of 44 mm, a cylinder radius of 31.7 mm and an axial length of 76 mm from the inlet plane to the upstream blade-root point. The bell occupies the first 30 mm, and the cylindrical section extends to a coaxial fan shroud immediately upstream of the blade roots. A six-blade axial fan with a 62 mm tip diameter runs in the 63.4 mm bore of the shroud at 18,000 rpm.
A backpack sprayer pump feeds liquid through a flexible hose to a flat-fan spray tip mounted just downstream of the handheld blower outlet. The handheld head draws air through a bell-shaped inlet and a cylindrical intake section into an axial fan. The spray tip points downstream into the discharge jet, which carries droplets toward the foliage. A two-stage trigger starts the blower with the first stage and opens a normally closed liquid valve with the second stage.
A pitot probe near the nozzle exit and a flush static pressure tap at the same axial position feed a differential pressure sensor. The axial fan draws air through a bell-shaped inlet and a cylindrical intake, then discharges it through the instrumented nozzle. A microcontroller compares the measured pressure difference with the setpoint for the selected airspeed and adjusts the motor drive using proportional-integral control.
A removable mesh screen covers the bell-shaped inlet, and four manifolded wall taps sample static pressure in the cylindrical section upstream of the fan. A differential pressure sensor compares this pressure with ambient pressure at a shielded port on the housing. A controller uses motor speed feedback to compare the pressure drop with a clean-screen baseline at the same speed. It illuminates a cleaning indicator when the measured drop exceeds the baseline by 150 Pa for three seconds.
Two injection-molded glass-filled nylon shells enclose the duct and motor. Internal ribs locate the duct, and screws draw the shells together at molded bosses.
A round intake grille closes the rear opening of the duct, and a tapered round nozzle forms the front outlet. Both openings center on the same longitudinal duct axis.
A molded rotor has seven swept blades that extend radially from a central hub. Each blade joins the hub along a filleted root whose inlet-side end forms the upstream connection point.
A 25-millimeter-long cylindrical throat runs from the end of the bell section toward the fan. It maintains a constant bore up to a plane 4 millimeters upstream of the blade roots.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The inner perimeter 54IP defines an at least partial aperture 55 (FIG. 6G), which, in one non-limiting embodiment, is completed by the closeout 36, to receive the outer duct 42 (FIG. 6H). The inner perimeter 54IP of the bellmouth fairing section 54 and the outer duct 42 are defined along the axis F to define an outer perimeter 56OP of the annular intake 56 (FIG. 6F).A · US 8,512,450 B2 · ¶ 60
Fan shroud 310 can include an inlet 312 and an out et 314. Inlet 312 can be adapted to receive the flow of air 360, while outlet 314 can be adapted to outlet the air 360.B · US 2015/0098818 A1 · ¶ 31
In some examples, the disclosure describes a fan shroud encircling a circular fan having a plurality of fan blades, where each fan blade has a blade depth and where the circular fan has a fan diameter.B · US 2015/0098818 A1 · ¶ 5
The surface between the outer perimeter 54OP and the inner perimeter 54IP of the bellmouth inlet faring section 54 provides a smooth bellmouth airflow surface to accelerate the airflow into the annular intake 56 (FIGS. 6A and 6E).A · US 8,512,450 B2 · ¶ 60
Similar to FIGS. 1 and 2, inlet 312 and outlet 314 can be substantially shaped as a bell mouth shape.B · US 2015/0098818 A1 · ¶ 35
An empty cell means only that no passage was reproduced there.
The attachment of the add-on filtration system with an existing inlet may introduce issues such as reduced inlet performance since the airframe mounted inlet is typically designed to operate optimally without the filtration system installed.A · US 8,512,450 B2 · ¶ 3
The relatively high airflow velocity may produce inlet performance sensitivity in which relatively small changes to the airflow within the EAPS or inlet may in some instances result in a relatively large inlet pressure loss.A · US 8,512,450 B2 · ¶ 4
Fan shrouds can reduce airflow recirculation from high pressure to low pressure side of the fan, can reduce airflow entrance & exit losses in and out of the fan, and/or can reduce airflow separation and vortices near the fan blade tips.B · US 2015/0098818 A1 · ¶ 2
Accordingly, there is a need for an improved bell mouth fan shroud and methods of designing and placing the bell mouth fan shroud.B · US 2015/0098818 A1 · ¶ 4
patent.fyi, US 2026/0354318 A1, claim 1, first published 2026-11-18T21:18:11-05:00, https://patent.fyi/US20260354318/, SHA-256 e7581bb47feef6c11a2375d9dcbd1d191542d65b912d39c8da927074285d4ce8