1.2Tray on linear guides
Two parallel rails hold the tray level as a linear actuator moves it out from beneath the outlet. A slide gate closes the outlet before the tray moves, and limit switches stop the actuator at both ends of travel.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two parallel rails hold the tray level as a linear actuator moves it out from beneath the outlet. A slide gate closes the outlet before the tray moves, and limit switches stop the actuator at both ends of travel.
A tray on a vertical pivot sweeps from beneath an offset outlet to a feeding recess behind the front wall. At the feeding stop, the front opening exposes the tray rim and leaves room for the pet's muzzle.
A reversible motor turns a toothed pulley that moves a timing belt clamped to the carriage. Guide blocks hold the carriage square, and two limit switches mark the filling and feeding positions.
A solenoid retracts the slide gate for a timed interval, allowing grain to fall through a chute into the bowl. A return spring closes the gate when the solenoid switches off.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A sealed hopper above a hatchery tank holds dry fish pellets and discharges them through a bottom outlet fitted with a slide gate. A gearmotor turns a shallow tray about a vertical shaft from beneath the outlet to a position beyond the hopper front wall and over the water. A follower on the tray engages a fixed ramp at the discharge position and tips the hinged tray floor to release the pellets into the tank.
A hopper with a gated bottom outlet sits above the tray at its loading position. A double-acting pneumatic rack-and-pinion actuator replaces the electric motor drive and couples directly to the vertical tray shaft. A directional valve sends compressed air to opposite sides of the actuator piston to swing the tray beneath the outlet or outward past the hopper front wall. Adjustable stops align the tray with the outlet and set its feeding position.
A hopper with a 25 mm bottom outlet sits above a 120 mm diameter tray whose center is 90 mm from its vertical pivot. A slide gate closes the outlet after a load cell beneath the tray measures 20 g of dry feed. A geared drive rotates the tray through 90 degrees in 4 seconds, placing the tray center 60 mm beyond the hopper front wall. The drive reverses through the same angle 15 minutes later.
A rotary tray feeder mounts to the head end of a livestock sorting stall equipped with an ear tag reader and an entry gate. The stall controller reads the animal identifier, closes the entry gate, and sends the assigned ration mass to the feeder controller. The feeder fills the tray beneath the hopper outlet, then rotates it beyond the hopper front wall into the stall. At the end of the feeding interval, the feeder retracts the tray and signals the stall controller to open the exit gate.
A flexible screw conveyor carries dry pellets from a bulk bin to a discharge tube above the feeder hopper. A low-level switch starts the conveyor, and a high-level switch stops it when the hopper refills. At each feeding cycle, a timed slide gate drops pellets from the hopper outlet into the tray below. A gearmotor swings the filled tray beyond the hopper front wall for access and returns it beneath the outlet after the feeding interval.
A load cell between the tray and its rotating arm measures feed mass when the arm is stationary. After each feeding interval, a controller returns the tray beneath the hopper outlet and measures the remaining feed. The controller subtracts the remaining mass from the next scheduled portion and pulses a motorized outlet gate until the tray reaches its target mass. The drive then rotates the tray beyond the hopper front wall.
A horizontal auger in a trough at the base of the container pushes grain through the sidewall opening. A downward chute carries the discharged grain to the receiving tray.
A vacuum blower draws grain up the wand into a separator above the receiving tray. The grain settles in the separator, and a flap releases it into the tray after the blower stops.
A molded polypropylene hopper has internal walls sloped at 60 degrees from horizontal toward a 45-millimeter circular outlet in its floor. Rounded internal corners let grain slide toward the outlet under gravity.
A shallow tray mounts on an arm that turns around a vertical steel pin. One stop places the tray under the grain outlet, and a second stop positions the front half of the tray beyond the container's front wall.
A reversible 12-volt gearmotor turns the tray pivot through a pinion and a sector gear. A cam on the pivot actuates a separate limit switch at each end of travel, and the controller stops the motor when the corresponding switch closes.
An electric linear actuator pushes and pulls a crank fixed to the tray pivot. Clevis joints accommodate the changing linkage angle as the actuator moves the tray between the filling and feeding positions.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The hopper assembly shell 4 is a canister that retains the feed within the hopper assembly 3 until the feed is dispensed.A · US 2015/0164044 A1 · ¶ 25
A collapsible pet feeder apparatus for holding pet food, comprising: a collapsible storage compartment adapted to be expanded to an elongated state for storing pet food, the storage compartment having a top portion, middle portion and bottom portion and an opening in the top portion and an opening in the bottom portion; a bowl portion positioned underneath the opening in the bottom portion of the collapsible storage compartment for holding pet food and wherein the bowl portioB · US 2019/0313604 A1 · claim 18
A bounce plate 17, which is disposed within the outer shell assembly 4 below the hopper assembly 3 when the hopper assembly 3 is inserted into the outer shell assembly 4, directs the feed that drops from the hopper assembly 3 to an opening to the feed tube 18.A · US 2015/0164044 A1 · ¶ 28
A collapsible pet feeder apparatus for holding pet food, comprising: a collapsible storage compartment adapted to be expanded to an elongated state for storing pet food, the storage compartment having a top portion, middle portion and bottom portion and an opening in the top portion and an opening in the bottom portion; a bowl portion positioned underneath the opening in the bottom portion of the collapsible storage compartment for holding pet food and wherein the bowl portioB · US 2019/0313604 A1 · claim 18
The top assembly 2 also includes an upper motor coupler 27 to operably connect a motor to the coupler assembly 13 to drive the screw 6.A · US 2015/0164044 A1 · ¶ 31
An empty cell means only that no passage was reproduced there.
Prior disclosed apparatuses are subject to clogging/jamming by the animal feed.A · US 2015/0164044 A1 · ¶ 5
The animal feeder has a hopper assembly that can be readily removed from the feeder housing and associated electronics for cleaning The hopper assembly is configured to resist pest access.A · US 2015/0164044 A1 · ¶ 2
More particularly, the present invention relates to a collapsible gravity pet feeder adapted to be locked for easy storage and transport.B · US 2019/0313604 A1 · ¶ 1
patent.fyi, US 2026/0354341 A1, claim 1, first published 2026-11-18T21:55:14-05:00, https://patent.fyi/US20260354341/, SHA-256 2a80d870fd5b089146d7776b74e58f6e90a3da43662c8a397dcb9980f9cc39d6