1.1Direct collar mounting
A split collar clamps around the blank over a thin elastomer liner. The guide ring seats in a socket formed directly in the collar wall, which transfers line loads into the blank.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A split collar clamps around the blank over a thin elastomer liner. The guide ring seats in a socket formed directly in the collar wall, which transfers line loads into the blank.
A concave bottom roller supports the line while two upright side rollers limit lateral travel. The rod mounts the cradle with its bottom roller on the side where line tension seats the line during normal use.
Two isolated saddles engage shallow flats on the outer edge of the ceramic ring. A spring clip engages a third flat and presses the ring into the saddles while leaving the intervening rim exposed.
The metal carrier bore has radiused entrances on both faces. A thin diamond-like carbon coating follows the bore and entrance radii to provide the line-contact surface.
A thin structural adhesive layer joins the flat rear face of the ceramic ring to the flat front face of the fixing ring. The fixing ring has a larger bore than the ceramic ring, so the ceramic bore and its rounded entrances carry the line.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two support legs fasten a fixing outer ring to a greenhouse curtain rail at a change in cord direction. A molded elastomer fixing inner ring sits inside the outer ring and holds a polished ceramic inner guide ring in an internal groove. The curtain drive pulls a braided cord through the ceramic bore, and the elastomer compresses locally under lateral cord loads.
A molded glass fiber reinforced polyamide ring replaces the metal fixing outer ring and bolts to two stamped support legs. Ribs on its outer face stiffen the ring around the leg attachment points. An annular recess on its inner face seats an elastomer fixing inner ring, whose internal groove captures the rounded rim of a ceramic inner guide ring.
The ceramic inner guide ring has an 18 mm clear bore, a 22 mm outside diameter, and a 4 mm axial width. An elastomer fixing inner ring provides a 1 mm radial layer between the ceramic and the fixing outer ring, which mounts on two support legs. Both bore entrances have a 0.8 mm edge radius so a leader knot up to 6 mm across passes over a rounded surface as the line changes angle.
Three support legs attach to the fixing outer ring, with two attachment points at the lower side quadrants and one at the bottom. The side legs slope toward opposite sides of the rod, and the center leg extends along the rod to a separate mounting point. The fixing inner ring seats inside the outer ring and holds the wear surface ring, while the three legs transfer lateral and fore-and-aft line loads to separate attachment points.
Two support legs bolt the fixing outer ring to the traversing carriage of a level wind reel. A compliant fixing inner ring seats inside the outer ring and captures a ceramic inner guide ring, with its bore facing the spool. A rotating grooved shaft drives the carriage back and forth across the spool so the ceramic bore sets the lateral line position during winding.
A fixture locates the assembled guide by its support legs and points the ring axis toward a camera. A front light exposes the fixing outer ring edge, and a backlight outlines the bore of the ceramic inner guide ring seated in the fixing inner ring. Software fits circles to the two edges and flags assemblies whose measured center offset exceeds 0.15 mm.
A bent stainless steel wire frame has two support legs that end in flattened feet aligned with the rod blank. Thread wraps secure the feet to the blank, and epoxy seals the wraps.
The guide ring has an oval opening with its long axis across the rod blank. Rounded entrance edges provide a continuous line-contact surface as the line moves laterally across the opening.
A rigid stainless steel fixing outer ring surrounds a molded polyurethane fixing inner ring. The polyurethane ring compresses around an alumina guide ring and engages a shallow groove in its outer rim to retain it axially.
A split spring stainless steel fixing inner ring snaps into an internal groove in a machined aluminum fixing outer ring. Inward lips on the spring ring capture a silicon carbide guide ring at both axial faces.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Of two legs of the fishing line guide illustrated in FIG. 3 in the description of this embodiment, the leg that may substantially linearly extend from the ring holding section (fishing line guide section) 8a to be connected to a fixed portion may be referred to as a main leg portion (first leg portion) 8c which may be fixed to the rod.A · US 2014/0373427 A1 · ¶ 44
Then, the guide ring 7 may be fitted into the ring holding section 8a of the completed frame 8 by using a usual technique to be fixed by using an adhesive or the like.A · US 2014/0373427 A1 · ¶ 59
One such configuration is shown in FIG. 1, wherein an innermost one of the nested rings 54 is attached to the last extended movable sections 56 of an associated pair of hydraulic cylinders 58. Similarly, an outmost one of the nested rings 60 is attached to the first extended movable sections 62 of another associated pair of hydraulic cylinders 58.B · US 11,903,450 B1 · ¶ 28
An empty cell means only that no passage was reproduced there.
In a case where the multiple fishing line guides described above having a metal frame are mounted on the fishing rod that is reduced in weight, the weight of the rod as a whole increases.A · US 2014/0373427 A1 · ¶ 6
Accordingly, when folding is performed during the bonding, the respective thin fibers are folded to cause a problem of weakened strength.A · US 2014/0373427 A1 · ¶ 8
The present invention discloses a platform shoe assembly that allows a person of short stature to appear taller or to reach items that otherwise would be out of reach.B · US 11,903,450 B1 · ¶ 6
What is lacking in the prior art is a platform shoe assembly comprising a pair of articles of footwear wherein each sole has a recess from which a plurality of rings is selectively extensible for increasing an effective height of a user.B · US 11,903,450 B1 · ¶ 7
patent.fyi, US 2026/0354362 A1, claim 1, first published 2026-11-18T21:55:14-05:00, https://patent.fyi/US20260354362/, SHA-256 04fda130d98e1736a67ca3ffeb32655bbf82b052fe413a5b9ac6a75b47f01607