1.1Dock molded into support
The tray wall and the dock form a single molded plastic part. A pocket in the wall holds the base magnet behind the surface where the receptacle sits.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The tray wall and the dock form a single molded plastic part. A pocket in the wall holds the base magnet behind the surface where the receptacle sits.
A stainless steel pin with peened ends joins the receptacle to the base. The receptacle pivots outward to expose the accessories and swings back until the magnets hold it closed.
The concave underside nests against a convex saddle on the base. Magnets embedded beneath the curved surfaces pull the parts together while the saddle limits sideways movement.
A low-carbon steel disk sits flush with the underside of the receptacle. The base magnet attracts the disk and holds the receptacle until the user lifts it away.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Bases with sealed magnets clamp to greenhouse bench uprights. Each tray has a flat rear wall with embedded magnets and a forward pocket that holds plant labels upright. A worker lifts the tray by its upper lip, pulls it free, and presses it against a base at the next potting station.
A low-carbon steel plate replaces the magnet in the flat rear portion of the receptacle. The plate sits flush in a molded recess, and the base magnet attracts it through a thin corrosion-resistant coating. A molded tab at the top lets the user peel the receptacle away while the receiving pocket retains its contents.
A switchable permanent-magnet module replaces the fixed magnet in a base that clamps to a support. The module has a lever that rotates an internal magnet within a steel housing, directing magnetic flux through the docking face in one position and through the housing in the other. In the first position, the exposed pole faces attract the magnets in the flat back of the receptacle. Turning the lever to the second position reduces the holding force so the user can lift the receptacle away by its rim.
Four bases mount with countersunk screws along a 300 mm support strip at 70 mm center-to-center spacing. Each base contains a 16 mm diameter disc magnet, and each 55 mm wide receptacle carries a matching disc magnet in its flat rear wall with opposite poles facing at the joint. The spacing leaves a 15 mm gap between adjacent receptacles so each pocket pulls straight off its base.
Each magnetic base attaches to a slotted kayak accessory rail with a captive T-bolt and a hand knob. Loosening the knob lets the base slide along the rail, and tightening it clamps the base at the selected position. A receptacle with rear magnets docks against the base, and a spring clip on its receiving portion grips the handles of fishing pliers.
Each base contains a Hall-effect sensor beside its coupling magnet and connects to a microcontroller. During setup, the controller records the field readings with the base empty and with a receptacle installed, then stores their midpoint as the detection threshold. When a reading crosses the threshold and stays on the new side for 200 milliseconds, the controller logs the base number, docking state, and time.
The receptacle magnet attracts a low-carbon steel plate fixed in the base. The user lifts one edge of the receptacle to separate it from the plate.
Slits in a foam insert fixed to the base grip the hook bends. The receptacle encloses the flies with clearance around them and lifts off the magnetic dock for access.
A folded stainless steel spring clip on the rear of the base slides over a belt or webbing strap. An inward return at the free end grips the lower edge of the strap.
An axially magnetized ferrite disk seats in a circular pocket in the base with one pole face toward the receptacle. A thin plastic cap seals the pocket against water and grit.
Two axially magnetized disk magnets sit in blind pockets in the flat receptacle floor. Each disk faces a corresponding base magnet with opposite poles facing across the joint.
A closed-cell foam pad sits in the receiving portion and contains parallel slits spaced 6 mm apart. The walls of each slit compress around an inserted hook bend and hold the fly in place.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A roof standoff device for use in mounting an object to a roof, said standoff device comprising: a base bracket having at least one mounting hole for receiving an attachment element for attaching the base bracket to a roof surface, said base bracket further including a first threaded attachment element; a flashing having: a raised section with an upper surface and a flashing aperture extending through said raised section, wherein said flashing aperture is configured for alignA · US 2015/0013237 A1 · claim 1
The detachable receptacle may be removably coupled to the handle of the cosmetic implement by a variety of attachment means, such as by snap fit, screw threads, a twist lock mechanism, magnetic force, interference fit, combinations of any of the foregoing, or the like.B · US 2015/0055998 A1 · ¶ 23
An empty cell means only that no passage was reproduced there.
However, these known shapes have the disadvantage that two shapes are needed to form the interlock, limiting the configurations and increasing the costs for the creation of a male and a female part.A · US 2015/0013237 A1 · ¶ 2
The present invention discloses a set of shapes that function as both the male and female part of the interlock, allowing a single shape to interlock with its identical shape.A · US 2015/0013237 A1 · ¶ 7
Carrying two separate items is not only cumbersome, but it increases the likelihood of loss of a brush or product, thereby rendering the other useless.B · US 2015/0055998 A1 · ¶ 1
Additionally, carrying a brush and its cosmetic product separately increases the likelihood that a certain cosmetic product might not always be accompanied by the right type of applicator for its use.B · US 2015/0055998 A1 · ¶ 1
patent.fyi, US 2026/0354363 A1, claim 1, first published 2026-11-18T21:55:14-05:00, https://patent.fyi/US20260354363/, SHA-256 7083ce99b1df758984dc1f746eb37a7fcc24cd1fabd3bdb6756d03998a0b52c8