1.1Barbell shaped base
The end pads carry the outer rod guides, and the web carries the intermediate guides and the central suction cup. A molded rib along the web limits bending between the end pads and the suction mount.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The end pads carry the outer rod guides, and the web carries the intermediate guides and the central suction cup. A molded rib along the web limits bending between the end pads and the suction mount.
A C-frame fixed beneath the midpoint of the base straddles the edge. A hand screw presses a swiveling rubber pad against the lower face while a fixed pad bears against the upper face.
Two underside cups sit at 15 percent and 85 percent of the base length, measured from the same end. Each seals independently against the mounting surface, and the distance between the cups helps resist twisting from an off-center rod load.
Two screws secure each guide bracket to threaded inserts in the sidewall. The brackets project laterally and hold upward-facing guides that receive rods lowered from above.
Three upward-facing guides sit side by side across a widened base. Each guide cradles a separate rod that extends parallel to the base length, and the guide spacing sets the lateral clearance between rods.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rectangular base carries a central underside suction cup and three spaced U-shaped guides along its upper face. The cup attaches to the clean glass deck of a laboratory instrument cart. The guides support a run of flexible tubing between a benchtop pump and a collection vessel, and their open tops let an operator lift out the tubing with both ends connected.
A rubber-coated pot magnet replaces the suction cup at the midpoint of the rectangular base. A countersunk screw fastens the magnet to the underside with its head recessed below the contact face. The magnet grips a flat steel panel while spaced U-shaped guides on the upper face support rods that lift out through the guide openings.
A rectangular base measures 180 mm long, 45 mm wide, and 8 mm thick and carries a 40 mm diameter suction cup centered on its underside. Four U-shaped guides with 12 mm clear openings sit at 40 mm center-to-center spacing, with the outer guide centers 30 mm from the base ends. The guides align along one axis to support an 8 to 10 mm diameter shaft at four points.
A 360 mm rectangular base carries a central underside suction cup and a longitudinal T-slot along its upper face. Three identical open U-shaped guides each attach to a sliding T-nut with a clamp screw. The operator sets the center-to-center distance between adjacent guides from 40 to 140 mm and tightens the screws to place the supports beneath straight sections of the article.
Two rectangular holders attach by their central underside suction cups to a smooth tray seated inside a sliding boat storage drawer. The bases sit parallel to one another and transverse to the rods, with corresponding U-shaped guides in each row aligned along the rod axes. Each rod rests in one guide on each base and lifts through both openings when the drawer is extended.
A central underside suction cup connects through a tee to a pressure sensor and a miniature diaphragm pump with a check valve. The pump, sensor, and controller sit inside the rectangular base beneath a row of open U-shaped guides. The controller starts the pump when the cup cavity falls below 25 kPa of vacuum relative to ambient pressure and stops it at 40 kPa. A manual vent admits air to detach the holder after the pump is switched off.
An injection-molded glass-filled nylon base measures 240 mm long by 60 mm wide and has rounded corners. Longitudinal ribs on the underside stiffen the base between its ends and the central mounting boss.
A 75 mm elastomer suction cup mounts beneath the longitudinal midpoint of the base. Closing an over-center lever lifts the cup center while its rim remains sealed, reducing pressure in the cavity.
Three rigid U-shaped guides bolt to threaded inserts on the upper surface at 70 mm intervals. A replaceable 2 mm elastomer liner cushions each saddle and leaves the top opening clear for rod insertion.
Three upward-opening U-shaped guides and the base form a single injection-molded polypropylene part. Each guide has a 24 mm clear opening and a rounded saddle, and molded fillets reinforce the guide roots.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The rod holder base 12 is attached to a platform 16 that supports other components of the side rigger 10.A · US 2007/0119089 A1 · ¶ 22
The rod holder base 12 is attached to a platform 16 that supports other components of the side rigger 10.B · US 2008/0053361 A1 · ¶ 22
Two additional rod holders 18A, 18B, are mounted to the platform 16 to support the addition of two additional fishing rods.A · US 2007/0119089 A1 · ¶ 22
Two additional rod holders 18A, 18B, are mounted to the platform 16 to support the addition of two additional fishing rods.B · US 2008/0053361 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
The side rigger extends a fishing line to the side of the boat during trolling in order to prevent the fishing line from entangling with other fishing lines originating from the boat.A · US 2007/0119089 A1 · ¶ 1
Thus, a needs exists to provide a simple, portable, and inexpensive rigger to allow boats to extend fishing lines to the side of the boat to reduce entanglement of lines, and so that a traditional expensive and bulky outrigger does not need to be employed.A · US 2007/0119089 A1 · ¶ 7
The side rigger extends a fishing line to the side of the boat during trolling in order to prevent the fishing line from entangling with other fishing lines originating from the boat.B · US 2008/0053361 A1 · ¶ 1
Thus, a needs exists to provide a simple, portable, and inexpensive rigger to allow boats to extend fishing lines to the side of the boat to reduce entanglement of lines, and so that a traditional expensive and bulky outrigger does not need to be employed.B · US 2008/0053361 A1 · ¶ 7
patent.fyi, US 2026/0354364 A1, claim 1, first published 2026-11-18T21:55:14-05:00, https://patent.fyi/US20260354364/, SHA-256 4a9dade3039b6c6524c3b411ca575e63dead7a2b4b26497105ced301c4f8bd1c