1.1Valve seats at chamber wall
A valve block seals against the chamber wall with a perimeter gasket. The two valve seats face the chamber and use the chamber volume as their common flow junction.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A valve block seals against the chamber wall with a perimeter gasket. The two valve seats face the chamber and use the chamber volume as their common flow junction.
Each diaphragm moves toward or away from an annular seat on one branch of a common port. A pivoting lever opens one seat as it closes the other, changing the division of flow.
Each spool slides across a metering window to vary the open area between its pump port and its conduit port. A pressure controller opens the supply valve to raise conduit pressure and opens the withdrawal valve to lower it.
A diaphragm regulator reduces cylinder pressure to a setpoint above the highest operating pressure in the conduit. The supply spool divides the regulated flow between the conduit and a vent branch.
The supply valve admits gas through tubing connected to one chamber fitting. The first conduit serves as the withdrawal path through a second fitting, and both fittings communicate through the chamber volume.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
The first conduit connects a suction cup to the working ports of two proportional spool valves at a shared manifold. One valve connects the manifold to the pump intake or admits filtered room air to the intake, and the other routes pump discharge to the manifold or to a muffled exhaust. The intake valve draws the cup down during pickup, then shifts toward room air as the discharge valve sends a short pulse to the cup for release.
Each three-port valve uses two independently driven proportional poppet cartridges in place of a spool. Both cartridges share the pump-side port, with one cartridge opening toward the working conduit and the other opening toward a reservoir. Current drivers vary the two poppet lifts independently, setting the division of flow between the working conduit and the reservoir on both the intake and discharge sides.
Each three-port valve uses a rotary spool in a stationary sleeve in place of a spool that slides along a bore. A central passage connects the pump-side port to two profiled slots, and rotation progressively changes the overlap of each slot with the working or bypass port. Geared stepper motors turn the two spools independently, with one valve serving the pump intake and the other serving the discharge at the shared conduit.
A diaphragm pump rated for 0.5 liters per minute connects to two proportional spool valves, and an 80 mm length of tubing with a 2 mm inside diameter connects their common working passage to a rigid 20 mL test vessel. Both third ports connect to room air through separate filters. A controller cycles between −1 and +1 kPa gauge pressure every 4 seconds, using vessel pressure to trim the active spool opening and routing the inactive pump side to room air.
A gear pump, two oil-compatible proportional spool valves and a single-acting spring-return test cylinder share a hydraulic circuit. The cylinder cap port connects to the working ports of both valves, and each third port connects to a vented oil reservoir, with the intake-side reservoir line terminating below the oil level. The discharge valve meters oil into the cylinder during loading while the intake valve draws from the reservoir. During unloading, the return spring drives oil toward the pump intake through the intake valve, while the discharge valve routes pump output back to the reservoir.
A pressure transducer mounts near the working end of the conduit, and a linear position sensor mounts on each spool. A controller compares measured pressure with a programmed waveform and commands the discharge-side spool to raise pressure or the intake-side spool to lower it. The controller routes the opposite pump connection through its third port and uses separate position feedback loops to track the two spool commands.
A compressed-gas jet entrains gas from the withdrawal valve and discharges the mixed stream through a diffuser. The withdrawal spool meters gas from the conduit into the ejector suction connection.
A braid-reinforced silicone hose runs between the chamber fitting and a tee that serves both valve branches. Barbed fittings and compression collars secure and seal the two ends.
A cylindrical spool carries two sets of tapered grooves that overlap sleeves with radial metering windows. Axial travel increases the exposed area at the second port while decreasing the exposed area at the third port.
A voice coil moves each spool against a centering spring. A linear position sensor measures spool travel, and a controller adjusts coil current to hold the commanded opening.
A machined manifold routes the withdrawal valve’s first port to the pump intake and the supply valve’s first port to the pump output. Two drilled passages join the valves’ second ports to a common socket that seals around the conduit end with an O-ring.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The fluid conduit is configured as a monolithic tubular body that includes a first conduit end, a second conduit end, a first coupling and a second coupling.A · US 2020/0332921 A1 · abstract
Furthermore, proportional spool valve 1 comprises two working connections A, B which can be connected, preferably alternately, to the pressure connection P and the tank connection T by displacing valve spool 3 in order for two pressure chambers of the displacement pump to be supplied with oil pressure or to be connected to the low pressure side to adjust the displaced volume, thereby causing an adjustment of an actuator of the displacement pump and manipulating the displacedB · US 2021/0033087 A1 · ¶ 42
In the case at hand, proportional spool valve 1 is configured as a 4/3-way valve and comprises an axial pressure connection P at the end face which is connected to the pressure side of an oil circuit comprising a displacement pump within the scope of the system. In valve housing 2, proportional spool valve 1 also comprises a tank connection T at the wall, which is connected to a low pressure side of the oil circuit or to an oil reservoir.B · US 2021/0033087 A1 · ¶ 42
An empty cell means only that no passage was reproduced there.
This disclosure relates generally to fluid transfer and, more particularly, to an assembly for transferring fluid in, for example, a fluid transfer system for a gas turbine engine.A · US 2020/0332921 A1 · ¶ 2
For example, there is room in the art for a fluid transfer tube with a smaller, more compact form.A · US 2020/0332921 A1 · ¶ 3
The constancy per revolution or per stroke and therefore the proportionality to the pump speed is disadvantageous in oil circuits of motor vehicles in which the component to be supplied by the respective pump, in particular a combustion engine, has a fluid demand (oil demand) in one or several speed range(s) of the displacement pump that is lower than the volume flow resulting from the proportionality.B · US 2021/0033087 A1 · ¶ 3
The assembly of the spring holder according to the state of the art can lead to mechanical deformations and desired forces on the valve housing and/or on the valve spool, thus having a negative impact on functionality.B · US 2021/0033087 A1 · ¶ 5
patent.fyi, US 2026/0354372 A1, claim 1, first published 2026-11-18T21:55:14-05:00, https://patent.fyi/US20260354372/, SHA-256 b550cda650c7cc948409e30afcc0659af3c788151f3204d964aa55be86319fc7