1.1Sheet forming with platens
An indexing belt carries a metered portion of masa onto a fixed lower platen. A pneumatic cylinder lowers a flat upper platen against adjustable stops that set the sheet thickness, then retracts to let the belt advance.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An indexing belt carries a metered portion of masa onto a fixed lower platen. A pneumatic cylinder lowers a flat upper platen against adjustable stops that set the sheet thickness, then retracts to let the belt advance.
A belt with low sidewalls carries a bed of masa to a discharge edge above the roller intake. The belt turns downward around its end pulley, and a scraper releases adhering masa so it falls into the intake.
A stainless steel plate anchors to a structural wall beside the sheeter. Two clevis lugs on the plate hold a vertical hinge pin in double shear, and the transverse support turns on bushings around the pin.
Two parallel guide rails carry the transverse support on linear bearing blocks. The operator slides the support horizontally until the nozzle clears the sheeter, and a spring-loaded pin holds the carriage at either end of its travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A screw feeder pushes deaired ceramic clay through a rigid pipe and a slot nozzle into a pair of counterrotating rollers. A transverse beam on a vertical pivot beside the rollers carries the feeder, pipe, and nozzle. A locating pin holds the nozzle parallel to the roller axes during sheeting. With the feeder stopped, the beam swings clear to expose the roller inlet for washdown.
An open stainless steel vibratory chute replaces the feed pipe and carries crumbled masa from a metering hopper to a rectangular nozzle. The chute and its drive sit on isolation mounts on the transverse support, with the nozzle fixed above the sheeter inlet. Chute vibration advances the crumbs, and the nozzle spreads the feed across the roller inlet. The hopper gate closes and the drive stops before the support swings away from the rollers.
A 900 mm transverse support carries two 280 mm slot nozzles with centers spaced 320 mm apart over a 700 mm roller face. A common hopper supplies two independently adjustable screw feeders, each connected to one nozzle. The rollers form two parallel sheets with a nominal 40 mm space between them at the nozzle outlets. Mechanical stops set the feed position and a service position 100 degrees away.
Rotary slitting wheels downstream of the sheeter cut narrow strips from both edges of the masa sheet. Chutes beneath the slitting wheels drop the strips onto a cleated return belt, which discharges into the upstream mixer. An adjustable fresh masa feeder supplies the mixer, and a screw feeder sends the blended masa through a flexible conduit to the nozzle on the swing support. The return belt and mixer stand beside the line outside the travel of the support.
A geared electric actuator turns the transverse support around the vertical post, and proximity switches detect the feed and cleaning positions. On a cleaning request, a controller stops the feed pump and rollers, opens a pressure relief valve to the supply hopper, and waits for a line pressure sensor to confirm depressurization. The controller then moves the nozzle over a grated wash station where spray headers rinse the nozzle exterior. The controller enables feeding when the feed position switch and the support latch switch both confirm engagement.
An ultrasonic level sensor mounted beside the nozzle measures the height of the masa bank just upstream of the roller gap. A controller uses roller speed to set the base speed of a variable speed feed screw. The controller raises screw speed when the measured bank falls below its target and lowers it when the bank rises above the target. A position switch on the pivot stops the screw and suspends level control when the nozzle leaves the feed position.
An operator loads a weighed batch of masa through a chamber hatch and latches the hatch. A hydraulic ram pushes the masa through a nozzle mounted directly against the chamber outlet face, with ram speed setting the feed rate.
Sliding hangers on the rail carry a flexible feed hose, and the transverse support grips a mounting flange on the nozzle body. A slack loop in the hose follows the nozzle as the support swings clear of the sheeter.
Two counter-rotating stainless steel rollers draw masa through the gap between them. A handwheel turns linked lead screws that move both bearing blocks of the upper roller together to maintain a uniform gap across the working width.
A stainless steel nozzle widens from a round inlet into a tapered chamber that feeds a rectangular outlet. The long edge of the outlet runs parallel to the roller axes, and a removable lip plate sets the slot height.
A reinforced, smooth-bore food-contact hose carries masa from the pump outlet to the nozzle inlet. Gasketed clamp fittings at both ends release the hose for washing.
A stainless steel transverse arm turns on a vertical pin in sleeve bushings, and a cushioned clamp secures the conduit to the arm. A spring-loaded indexing pin engages two sockets that hold the nozzle over the roller intake or beside the sheeter for cleaning.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
High production tortilla sheeters feed masa from a hopper between a pair of large, stainless steel rollers which roll the masa into a sheet of substantially uniform thickness.A · US 2015/0110938 A1 · ¶ 6
High production tortilla sheeters feed masa from a hopper between a pair of large, stainless steel rollers which roll the masa into a sheet of substantially uniform thickness.A · US 2015/0110938 A1 · ¶ 6
Viewed schematically but reversed in operation the chamber 10 could represent pressurizing masa means with masa within it and send the masa out through the conduit 11 and the masa could be expelled or extruded out of the nozzle 12 onto a flat surface.B · US 9,420,802 B1 · ¶ 20
Viewed schematically but reversed in operation the chamber 10 could represent pressurizing masa means with masa within it and send the masa out through the conduit 11 and the masa could be expelled or extruded out of the nozzle 12 onto a flat surface.B · US 9,420,802 B1 · ¶ 20
An empty cell means only that no passage was reproduced there.
More specifically, the present inventions relate to sheeting devices which control the spacing of rollers used to roll a comestible product to a desired thickness.A · US 2015/0110938 A1 · ¶ 3
One challenge that remains, however, is to accurately control the thickness of the masa sheet before cutting.A · US 2015/0110938 A1 · ¶ 7
A system for enabling and/or facilitating the automatic depositing and pressure smearing or spreading or buttering of thick viscous fluids such as; grease, clay in a plastic state, molten plastic, or tamale masa hereafter: masa, onto a leaf.B · US 9,420,802 B1 · ¶ 1
The system provides that the masa be delivered and/or pressed with enough force during lateral movement to effect adherence of the masa to the leaf so that the masa will not fall off the leaf during further handling of the now masa buttered leaf.B · US 9,420,802 B1 · ¶ 1
patent.fyi, US 2026/0354390 A1, claim 1, first published 2026-11-18T22:28:45-05:00, https://patent.fyi/US20260354390/, SHA-256 19e32982ffad3921f8fa82120dbec2a432ec7c63a910cc2835ab4757b8b74b91