1.1Open bottom with side suspension
Two inward-facing tabs project from opposing sidewalls and bear on the underside of an annular shoulder near the top of the article. The lower end hangs clear of the bottom opening.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two inward-facing tabs project from opposing sidewalls and bear on the underside of an annular shoulder near the top of the article. The lower end hangs clear of the bottom opening.
An acetal clip molded into the first sidewall flexes over the article as it pivots into position. The clip seats behind a shoulder on the article and presses it against an elastomer pad on the sidewall.
A tapered polymer post projects from the base and seats in a matching recess at the lower end of the article. An elastomer ring around the post grips the recess wall and retains the article in the upright position.
Three elastomer ribs grip the article when its lower end reaches a fixed stop. A thumb lever lifts an ejector pin through the stop and pushes the article past the ribs so it can be withdrawn along its axis.
Two parallel rails guide a sliding cradle laterally from a base detent toward the first sidewall. At the end of travel, a magnet in the sidewall attracts a steel strip on the article and holds the article against the wall while the cradle maintains its orientation.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A bench cradle holds a handheld inspection probe with a low-carbon steel plate recessed into its handle. In the first position, two saddles on the cavity base support the probe horizontally. The probe pivots on the forward saddle until the handle rises 35° and the steel plate seats against a permanent magnet recessed in the first side, exposing the handle for pickup.
A stainless steel leaf-spring clip on the first side replaces the magnetic retaining pair, and a molded shoulder on the article provides a catch surface. The base supports the article in the first position. As the article rotates into the second position, the shoulder rides over a ramp on the clip and the clip snaps behind it. A release tab deflects the clip to let the article return to the base.
A removable cradle insert replaces the fixed base and further side supports inside a rigid casing. Two elastomer-lined saddles on the insert support the article in the first position, and a rigid stop locates one end. Inserts with different saddle profiles place the steel pad of each supported article shape at the same location in the second position. The article rotates on the saddle nearest the stop until the pad seats against the magnet in the first side.
A cavity accepts articles measuring 80 mm and 110 mm long, each with a steel pad centered 10 mm from its free end. In the first position, each article rests on the base with its opposite end located by a common pivot seat. Two recessed magnets in the first-side rail have centers 70 mm and 100 mm from the pivot along the 40° raised orientation. Each pad aligns with its corresponding magnet when the article rotates against the rail.
The cavity forms the upper tray of a low-voltage charging dock for a rechargeable article. Two spring-loaded contacts in the base mate with recessed charging pads on the article in the first position, and a base switch enables the dock output when the article seats. When the article rotates upward, it releases the switch and separates the contacts. The magnet on the first side then holds the article in the second position for pickup.
A geared motor drives an eccentric cam beneath a slot in the cavity base, and a base switch detects a seated article. On a button press with the switch closed, the cam raises the free end while a rounded seat guides the opposite end. At 45°, a magnet on the first side captures the article and a second switch confirms that it is seated against that side. The controller then returns the cam below the base.
An injection-molded base forms a shallow recess that matches the lower end of the article. A 1 mm silicone pad at the bottom compresses under the seated article.
A nickel-plated neodymium magnet sits in a molded pocket behind a 0.5 mm polymer skin on the first sidewall. The magnet attracts a low-carbon steel strip embedded in the article where it faces the pocket.
Two polycarbonate sidewalls extend from the base on opposite sides of the cavity. Each sidewall has a rounded longitudinal rib that guides the article and limits lateral movement.
The lower end of the article pivots about a rounded lip on the base until the article meets a stop on the first sidewall at 40° from the seated position. A magnet behind the stop attracts a steel insert in the article and holds it against the sidewall.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A molding tool comprising: a first plate; the first plate having a surface; the surface comprising a mold cavity; the mold cavity having a side wall and a bottom wall; the mold cavity having an orifice defining an opening through the bottom wall of the cavity; the orifice assembled with a porous insert.B · US 2016/0029688 A1 · claim 1
According to this process, a constituent plastic of said molding or of said plastic window respectively is introduced into a molding cavity in which at least one ferromagnetic insert, such as a trim, has been placed beforehand, and said insert is held in position in said molding cavity during the introduction of said plastic by at least one magnet which can move between two positions, an active position A in which it exerts an attractive force on said insert across the internA · US 9,114,556 B2 · ¶ 9
It shall be seen that in FIG. 7, the side walls 145 may form a continuous contour with the floor 150.B · US 2016/0029688 A1 · ¶ 69
According to this process, a constituent plastic of said molding or of said plastic window respectively is introduced into a molding cavity in which at least one ferromagnetic insert, such as a trim, has been placed beforehand, and said insert is held in position in said molding cavity during the introduction of said plastic by at least one magnet which can move between two positions, an active position A in which it exerts an attractive force on said insert across the internA · US 9,114,556 B2 · ¶ 9
An empty cell means only that no passage was reproduced there.
This system is difficult to manufacture and to use, as it requires the power supply for the electromagnet to be controlled.A · US 9,114,556 B2 · ¶ 6
Another object of the invention is to enable the insert to be retained through the wall of the molding cavity, without having to provide a particular zone and without having to use a surface seal in the molding cavity.A · US 9,114,556 B2 · ¶ 8
Rotary die cutters and rotary die molds are a popular method of forming consumable food products, however, rotary die cutters and rotary die molds may not be optimal for creating three dimensional food items.B · US 2016/0029688 A1 · ¶ 2
In a variation, the entire mold cavity and/or an entire surface of the ejection plate may be made of a porous material.B · US 2016/0029688 A1 · ¶ 3
patent.fyi, US 2026/0354450 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354450/, SHA-256 7c9bf503fc296279ca8840ffd5f0d6a23c6391d0adca32ac26c5bbfded7206f3