1.1Housing with integral end wall
A molded cup forms the sidewall and the closed end of the housing. The reservoir and heater assembly slide through the open end, and a gasketed cap closes that opening.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A molded cup forms the sidewall and the closed end of the housing. The reservoir and heater assembly slide through the open end, and a gasketed cap closes that opening.
A snap ring holds an internal bulkhead against a silicone face gasket seated on the shoulder. The open section beyond the bulkhead provides a dry recess for electrical contacts.
A nonporous diaphragm separates the liquid from a vented air chamber and rolls along the reservoir wall as liquid leaves. Capillary suction at the heater wick draws liquid through an outlet while ambient air enters the dry side through the vent.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two recessed silicone plugs seal opposite ends of a tube and form end pockets for water. A hydrophilic polyester felt sleeve occupies the middle space and draws water from both pockets. A felt tab extends through a compression fitting in one plug and feeds the rear surface of a vibrating mesh that atomizes water into a plant propagation chamber.
A sintered borosilicate glass sleeve replaces the liquid storage member in the middle space and surrounds a separate aerosol duct. Compliant seats in the two end seals locate the sleeve, and each end face contacts liquid through an opening in its seat. The interconnected pores retain liquid by capillary action, and a radial outlet in the sleeve contacts a wick that supplies a resistive heater.
Rigid thermoplastic end caps serve as the two sealing members and attach to opposite ends of a tube made from the same resin. An annular energy director molded into each cap melts during ultrasonic welding to form a continuous seal around the rim. A recess in each cap holds liquid against one end of the porous middle storage member, which feeds a wick in contact with the atomizer.
Two cup-shaped end seals each define a 0.60 mL liquid pocket, and their inward rims bound a 0.40 mL middle space. A porous storage pad fills the middle space and projects 1 mm through each rim into the corresponding pocket. A heater wick contacts the pad at its midpoint and draws liquid from it during atomization.
Two recessed end seals form liquid pockets on either side of a porous storage pad in the middle space. A miniature diaphragm dosing pump connects to a pickup tube that passes through one end seal and contacts the pad. The pump delivers liquid through an outlet check valve to a separate heater wick, and capillary flow from the end pockets replenishes the pad.
Two recessed end seals form liquid pockets at opposite ends of a nonconductive housing, and a porous storage pad spans the middle space. A pair of electrodes on the outside of the housing measures capacitance across the pad near the heater wick. The controller sets a low-liquid threshold from calibration measurements with the pad at known liquid contents. The controller samples capacitance between heater pulses and disables the heater when the reading falls below the threshold.
An extruded polycarbonate tube is cut to length, leaving an opening at each end. The bore provides a continuous seating surface for the two end seals.
A cup-shaped recess in the inward face of each end seal forms an end storage space. The housing bore between the two recesses forms the third storage space, and the open faces of the recesses connect all three spaces.
A polyester felt sleeve fits around a central airflow tube in the third storage space. Liquid wets the fiber surfaces, and the gaps between fibers retain a portion of the liquid by capillary action.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
These three components are arranged co-axially and contained within a rigid tubular casing 50. The refillable aerosol-generating article is in the form of a substantially cylindrical rod and has an outlet end 60 and a distal end 70 opposite to the outlet end.A · US 2017/0340018 A1 · ¶ 85
This may allow the heat diffuser to conveniently and easily pierce a seal at an end of an aerosol-generating article with which it is intended for use when the heat diffuser is engaged with the aerosol-generating article.B · US 10,499,690 B2 · ¶ 111
As used herein, the term “liquid retention medium” refers to a component that is configured to releasably retain a liquid aerosol-forming substrate. The liquid retention medium may be, or may include, a porous or fibrous material that absorbs or otherwise retains a liquid aerosol-forming substrate that it is brought into contact with while allowing the liquid aerosol-forming substrate to be released by vaporization.A · US 2017/0340018 A1 · ¶ 38
Thus, the liquid aerosol-forming substrate 216a is depicted as being already absorbed into the liquid retention medium 210a.B · US 10,499,690 B2 · ¶ 311
An empty cell means only that no passage was reproduced there.
One disadvantage of the e-vapor system is that direct heating of the liquid substrate with a heating coil risks overheating of the liquid, particularly when the cartridge is near to empty.A · US 2017/0340018 A1 · ¶ 4
However, a user may desire the wider variety of flavors that are possible with a liquid-based heated e-vapor system.A · US 2017/0340018 A1 · ¶ 5
patent.fyi, US 2026/0354457 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354457/, SHA-256 21f8600530cb2f706cf9f3cc58362aad500ea8d5b635b1398655ffd04bdc7b5a