1.1Residue cassette beside bowl
A horizontal duct carries the air and vapor mixture through a stainless steel fiber pad in the cassette. Droplets collect on the fibers, and capillary forces retain the liquid in the pad when airflow stops.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A horizontal duct carries the air and vapor mixture through a stainless steel fiber pad in the cassette. Droplets collect on the fibers, and capillary forces retain the liquid in the pad when airflow stops.
A vertical riser carries the mixture from the bowl outlet to an inlet in the base of the recycler. A compression gasket seals the joint between the two portions.
Punched stainless steel tabs project from alternating sides of the chamber and redirect flow toward the chamber wall. Each tab stops short of the opposite wall, leaving one continuous gas volume from the inlet to the mouthpiece.
Suction at the mouthpiece draws the mixture from the first chamber through the port into the second chamber. Condensate drains to the floor of each chamber, where it collects below the port.
The bowl outlet delivers the mixture into the second chamber. Suction at the mouthpiece draws gas through the upper and lower connecting passages into the first chamber, which supplies the mouthpiece.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A heated stainless steel sample cup holds a polymer coupon for outgassing measurements. Carrier gas passes over the coupon and carries released compounds down to a condensate sump at the lowest point of the flow route. A lateral passage leads from the sump headspace to two adjacent chambers linked by upper and lower passages. A sampling tube extends from the second chamber and delivers the gas to an analyzer.
A sintered alumina puck replaces the open collection volume of the residue reservoir and sits in a sealed pocket below the bowl. The descending passage discharges into a headspace above the puck, and a lateral outlet from that headspace feeds the first chamber. Liquid residue falls onto the puck and enters its pores by capillary action. Gas continues through the upper and lower chamber connections to the second chamber and exits through its mouthpiece.
A ferritic stainless steel sleeve around a ceramic bowl replaces the resistive heating element. A ferrite-backed induction coil surrounds the sleeve outside the sealed gas path, and a pressure sensor at the mouthpiece signals the coil driver when inhalation begins. The coil induces currents in the sleeve, which transfers heat through the ceramic wall to the bowl contents. The gas mixture descends to the lowest-point residue reservoir and then flows sideways into the first chamber, through the two chamber connections, and out the second chamber mouthpiece.
A single bowl feeds an 8 mL residue reservoir at the lowest point of the flow route. A manifold above the reservoir divides the gas into three parallel branches with equal lengths and 3 mm internal diameters. Each branch feeds a pair of 12 mL chambers joined by an upper passage and a lower passage. A common outlet manifold combines the flows from the three second chambers and delivers them to one mouthpiece.
A vacuum pump draws carrier gas from a heated bowl down past a residue reservoir at the lowest point of the flow route and then into a side-mounted two-chamber assembly. Upper and lower passages connect the chambers, and a heated transfer line connects the second chamber outlet to an infrared gas cell. A flow controller between the gas cell and the pump sets the sampling rate. A thermostatic jacket holds the transfer line and gas cell at the selected sampling temperature to limit condensation downstream of the reservoir.
An infrared emitter and photodiode face each other across a transparent prism molded into the wall of the lowest-point residue reservoir. The prism sits at the service fill level and returns light to the photodiode by total internal reflection when its inner face is exposed to air. When residue contacts the prism, the received signal drops, and a controller disables heater power after the signal stays below a calibrated threshold for two seconds. The lateral gas passage above the prism feeds the first chamber, and the upper and lower passages connect it to the second chamber and mouthpiece.
A drawn stainless steel cup fits directly beneath the bowl and seals against the bowl housing with a silicone gasket. A short vertical bore connects the bowl outlet to the cup, where the mixture turns toward a side outlet and leaves droplets on the cup wall.
The bowl and recycler portions mount side by side on a common base. A horizontal stainless steel tube carries the mixture from the bowl portion to the recycler, and silicone grommets seal both ends of the tube.
A borosilicate glass body contains two chambers separated by a fused glass partition. The first chamber contains an inlet aimed along its outer wall, and the second chamber contains the outlet to the mouthpiece.
Two bores cross the partition between the chambers, one just below the lid and one just above the floor. Gas passes through both bores into the second chamber, and a mouthpiece tube projects upward from its lid.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Gas trap 22 is created by the combination of a condensate sump 28 at the bottom of main condenser 20, a weir 30 inside sump 28, and a drain tube 32 that runs from the bottom of second condenser 12 to condensate sump 28.A · US 8,011,196 B2 · ¶ 17
Gas trap 22 is created by the combination of a condensate sump 28 at the bottom of main condenser 20, a weir 30 inside sump 28, and a drain tube 32 that runs from the bottom of second condenser 12 to condensate sump 28.A · US 8,011,196 B2 · ¶ 17
In the horizontal plane this liquid distribution element 33 is positioned in such a way on the top side 23a that liquid 24 dripping into the drip well 17 from the top hits this liquid distribution element 33. Due to the specific geometry the liquid 24, if present, is also correspondingly separated or enlarged in surface and drained towards the top side 23a in a targeted way.B · US 10,663,219 B2 · ¶ 61
An empty cell means only that no passage was reproduced there.
Due to the drawbacks of current heat-recovery chiller systems, there is a need for a refrigerant system that can recover waste heat more effectively without adverse system effects.A · US 8,011,196 B2 · ¶ 5
Another object of some embodiments is to provide a chiller with a refrigerant flow path to and through the heat-recovery condenser in such a way as to minimize the pressure differential between the chiller's two condensers.A · US 8,011,196 B2 · ¶ 8
The handling of the drip tray is not very convenient for the user and liquid dripping in splashes up again in an undesired way so that also portions of the niche are moistened in an undesired way by the splashing liquid.B · US 10,663,219 B2 · ¶ 7
In particular in this connection it is the task to provide a drip tray, which is easier to handle for a user and thus with regard to removal and insertion of the drip tray from the niche and into the niche is improved.B · US 10,663,219 B2 · ¶ 8
patent.fyi, US 2026/0354461 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354461/, SHA-256 f5fc0cdccf9e6e64d12c0ff8aa4b056d90379b0a9aef146ad6502df4f4905591