1.1Shallow circular housing
The housing has an outside diameter of 24 mm and an axial depth of 9 mm. A ceramic ring supports the coil beneath a central opening that receives the aerosol-forming material.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The housing has an outside diameter of 24 mm and an axial depth of 9 mm. A ceramic ring supports the coil beneath a central opening that receives the aerosol-forming material.
Three alumina posts space the end plates apart and leave open gaps around the coil. Grooves in the plates retain the coil ends, and a porous ceramic insert holds the aerosol-forming material within the coil.
A fired resistive trace on the underside of an alumina plate converts electrical power to heat. The plate conducts heat to a porous pad on its upper surface, and air passes over the pad to carry away the generated vapor.
A resistance wire winds around the exterior of a thin-walled alumina tube that forms the housing. The tube conducts heat from the coil to a porous insert in the bore, where incoming air picks up vapor.
A 5 mm cylindrical mandrel sets the coil bore, and the winding pitch increases from 0.8 mm at the inlet to 1.6 mm downstream. The closer turns pack more resistance wire into each millimeter of axial length and generate more heat per millimeter at the same current.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An elongate stainless steel tube carries dry nitrogen to an optical instrument. Four alumina supports center a nickel-chromium coil whose turn diameter is greatest near the axial midpoint. A low-voltage supply energizes the coil through ceramic feedthroughs, and an outlet thermocouple provides feedback for gas temperature control.
A photoetched nickel-chromium foil strip replaces the round-wire heating coil. The strip winds around an alumina sleeve with a waist at its midpoint, and shallow grooves in the sleeve set the turn spacing. Ceramic end rings retain the strip inside the elongate housing, and welded tabs connect it to the power circuit.
A 24 mm long nickel-chromium coil fits inside a housing with a 7 mm bore and winds around a hollow alumina former. The coil has 12 turns at a 2 mm center-to-center axial pitch, with a 5.0 mm outside diameter at both ends and a 3.5 mm minimum across the two middle turns. End terminals supply current to the continuous winding, and the former conducts heat to a cartridge inserted through its bore.
A metering pump draws liquid from a reservoir and delivers it through a capillary to the middle of a porous alumina sleeve. A coil with a larger turn diameter at the middle surrounds the sleeve, and both components sit inside an elongate housing with a longitudinal air passage. The controller preheats the coil before pulsing the pump, and air flowing through the passage carries aerosol from the heated sleeve to the outlet.
A continuous coil with a larger turn diameter around its midpoint sits on an alumina support inside the elongate housing. Two intermediate electrical taps divide the winding into three series sections, each connected across a separate isolated power channel. A thermocouple at each section feeds a controller that adjusts the corresponding channel duty cycle to hold its programmed temperature.
A servo winder feeds resistance wire through an adjustable forming head and changes the forming radius as successive turns pass through the head. A backlit camera measures the outside diameter of each turn and sends the measurement to the winder controller. The controller compares each reading with the stored axial profile and corrects the forming radius for subsequent turns. Ceramic end supports center the finished winding inside the elongate housing.
Two wire gauges of the same resistance alloy form a series winding, with welded joints between the center and end sections. The thinner center wire has greater resistance per unit length and releases more heat per unit length at the same current.
A stainless steel sleeve 36 mm long and 10 mm in outside diameter forms the housing. Inlet slots near the base feed air into the bore, and ceramic end rings center the coil and isolate it electrically from the sleeve.
An alumina liner and a glass-filled polymer outer sleeve form a housing 35 mm long and 13 mm in outside diameter. End collars hold the walls apart across a 1 mm annular air gap, and the liner supports the heater at both ends.
A nickel-chromium wire helix expands from a 4 mm inside diameter at the inlet to a 6 mm inside diameter at the outlet while maintaining a 1.2 mm pitch. Ceramic seats hold the end turns coaxially inside the housing around a tapered porous insert.
An iron-chromium-aluminum wire forms four turns with a 4 mm inside diameter and four turns with a 6 mm inside diameter, joined by a transition turn. Both sections share a longitudinal axis inside the housing and follow the two diameters of a stepped ceramic support.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As shown in FIG. 3, the tubular immersion heating element 40 have a tubular metallic sheath 50 and a resistance heating coil 52 disposed within the sheath 50 and separated therefrom by dielectrically insulating material 54.A · US 2009/0141850 A1 · ¶ 20
Referring to FIG. 2B, the a cartridge microreactor 100 is assembled by first taking a commercially available tubular heater with an incoloy outer sheath 110 and cutting a desired length (a).B · US 8,875,981 B2 · ¶ 33
As shown in FIG. 3, the tubular immersion heating element 40 have a tubular metallic sheath 50 and a resistance heating coil 52 disposed within the sheath 50 and separated therefrom by dielectrically insulating material 54.A · US 2009/0141850 A1 · ¶ 20
An empty cell means only that no passage was reproduced there.
It is desirable to also provide an improved heater design that will minimize the potential for heater sheath failures due to stress corrosion cracking in the future to avoid the need for additional repairs and personnel exposure to radiation.A · US 2009/0141850 A1 · ¶ 7
In one preferred embodiment, both material conditioning and surface conditioning treatments may be applied to existing heater sheaths during servicing of the pressurizer, to spare heater sheaths that are maintained in inventory or to newly manufactured sheaths, such that crack initiation is less likely to occur over extended plant operation.A · US 2009/0141850 A1 · ¶ 10
Accordingly, there is a need for an improved microreactor system that is capable of operating at high temperature and pressure ranges and is capable of producing highly dispersed and high surface area catalystsB · US 8,875,981 B2 · ¶ 4
The microreactor further includes a small open channel through the center of the deposited aerogel and the open channel reduces the pressure drop across the microreactor, and provides reactant and product exchange with the aerogel via diffusion.B · US 8,875,981 B2 · ¶ 7
patent.fyi, US 2026/0354467 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354467/, SHA-256 062629d869284260ac19afff31068914b9ca3e60dbc720b478e20c29a7dbbf10