1.1Direct contact blade heating
The user slides the article onto a ceramic blade with an embedded resistive track. The blade conducts heat into the substrate, and two spaced rails support the article while leaving its sides exposed.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The user slides the article onto a ceramic blade with an embedded resistive track. The blade conducts heat into the substrate, and two spaced rails support the article while leaving its sides exposed.
A spring clip presses the article's flat metal base against a machined face on the outside of the oven. A resistive heater inside the oven conducts heat through the wall and base into the substrate.
Three zirconia standoffs limit heat flow from the oven to an aluminum holder. A thermoelectric cooler draws heat from the holder as the oven warms, and a finned heat sink discharges that heat into a separate airflow path.
Two pairs of ceramic rollers center the oven radially while permitting its shell to slide along the oven axis. End stops limit axial travel to one millimeter, and a flexible lead supplies current as the oven moves.
Three stainless steel tabs welded to the oven shell hold it to the support ring throughout heating and cooling. A flanged liner lifts out through the article opening and carries away residue deposited on its inner surface.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A removable metal sample cup sits in a laboratory drying oven with its rim resting on an annular holder. A bimetal strip attached to the holder bends as the oven heats and drives a sliding pin into a radial hole in the cup rim. The pin holds the cup in place during drying and retracts as the holder cools, allowing the cup to lift out.
A sealed wax actuator sits in a bore in the oven holder with its plunger facing a pivoting hook. A metal bridge conducts heat from the oven to the holder and actuator, and the expanding wax drives the plunger to turn the hook behind a lug on the oven component. A return spring retracts the plunger and swings the hook clear as the holder cools.
A nickel-titanium wire runs along the heated holder between a fixed anchor and a bell crank. Heat conducted from the oven through the holder raises the wire above its transformation temperature, and contraction rotates the bell crank to drive a transverse pin into a hole in a tab on the oven component. As the holder cools, a torsion spring turns the bell crank back, re-extends the wire, and retracts the pin.
Three sliding latches sit in radial guides spaced 120 degrees apart around a removable oven flange. A bimetal coil anchored to the holder rotates a cam ring through 15 degrees between its cool and hot stops. Three inclined slots in the ring drive the latches inward by 1 mm so they enter matching recesses in the flange and restrain axial and rotational movement. As the coil cools, it turns the ring back and retracts all three latches.
A compression spring and a guided ejector plate sit beneath the removable oven component. Inserting the component compresses the spring, and a bimetal lever on the holder pushes a crossbolt into a groove in the component as the holder heats. When the holder cools, a return spring withdraws the crossbolt and the ejector lifts the component to a travel stop where its rim projects above the housing.
A thermistor measures the temperature of the holder, which receives heat through a metal mounting tab on the oven. When the controller detects heat mode and a holder temperature above the engagement threshold, a geared motor turns a pawl into a notch on the oven component. The pawl seats against a mechanical stop, and a position switch confirms engagement. After heater power switches off and the holder reaches a lower release threshold, the controller reverses the motor until a second switch confirms that the pawl is clear.
A cam on the door drives a steel latch into a groove on the oven flange during the final part of door travel. A switch enables heater power after the latch seats, and opening the door withdraws the latch.
An alumina tube receives the article, and a resistive track printed on the tube's outer wall supplies heat. A thermistor feeds a controller that regulates current in the heated mode, and a switch interrupts current in the non-heated mode.
A stainless steel holder rests against the oven flange at three raised contact pads. Heat conducts through the pads into the holder as the oven wall warms.
A bimetal strip on the holder bends as it warms and drives a steel pawl into a groove on the oven flange. The pawl seats against a rigid stop, and the strip withdraws it as the holder cools.
An aluminum spigot on the oven flange fits inside a stainless steel holder bore with radial clearance at room temperature. Heating expands the spigot more than the bore and creates a friction fit, and cooling restores the clearance.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As shown in FIG. 2, the heating element 120 is mounted within an aerosol-generating article receiving chamber of the aerosol-generating device 110. In use, the user inserts the aerosol-generating article 10 into the aerosol-generating article receiving chamber of the aerosol-generating device 110 such that the heating element 120 is directly inserted into the aerosol-forming substrate 20 of the aerosol-generating article 10 as shown in FIG. 2.A · US 2014/0305448 A1 · ¶ 188
The device comprises a heater for heating the cylindrically shaped aerosol-forming substrate.B · US 2020/0046026 A1 · ¶ 21
Heating is preferably done by heating portions of the receiving chamber, for example heating receiving chamber walls, or by heating a holder, for example holding pins, around which the substrate is rolled.B · US 2020/0046026 A1 · ¶ 45
An empty cell means only that no passage was reproduced there.
Direct contact between an internal heating element of an aerosol-generating device and the aerosol-forming substrate of a heated smoking article can provide an efficient means for heating the aerosol-forming substrate to form an inhalable aerosol.A · US 2014/0305448 A1 · ¶ 7
Furthermore, the overall heating energy required to generate an aerosol may be lower than would be the case in a smoking system comprising an external heater element where the aerosol-forming substrate does not directly contact the external heating element and initial heating of the aerosol-forming substrate occurs by convection or radiation.A · US 2014/0305448 A1 · ¶ 7
It would be desirable to have an aerosol-generating device and method not requiring an elaborate and costly manufacturing process for forming tobacco rods.B · US 2020/0046026 A1 · ¶ 3
By the rolling of the sheet of aerosol-forming substrate, the substrate does not need to be crimped for a subsequent gathering.B · US 2020/0046026 A1 · ¶ 7
patent.fyi, US 2026/0354471 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354471/, SHA-256 a36492c66fc060f2f31d80ec65800e1ad54d34144f21609f3c59928029257c52