1.2Heater recessed below the surface
A flat resistive heater sits in a recessed pocket beneath a flush ceramic plate. The precursor holder rests against the plate, which conducts heat from the resistor into the precursor.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A flat resistive heater sits in a recessed pocket beneath a flush ceramic plate. The precursor holder rests against the plate, which conducts heat from the resistor into the precursor.
A threaded collar draws the split collet into a tapered seat in the base. The taper presses the collet jaws against the constant-diameter stem, and friction holds the heater axially.
An annular groove in the base holds a preformed silicone gasket around the cooler section of the heater stem. A retaining ring compresses the gasket against the stem and groove wall to block condensate from entering the joint.
The flange rests on a counterbore shoulder in the base. Two shoulder screws enter from the side and engage a circumferential groove in the flange, limiting axial movement.
The lower shroud bolts to a frame crossmember and supports the heater flange on an annular seat. The upper shroud bolts to separate frame posts, and its inward lip limits upward flange travel while a gap separates the shrouds.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A ventilation test instrument uses a protruding resistance heater to generate tracer fog from an aqueous glycerol solution. Upper and lower shrouds capture a flange fixed to the heater and secure the assembly in a handheld housing. A continuous coating spans the heater and its junction with the base, and a metering pump feeds solution through a capillary onto the heated tip. A small blower directs the resulting fog through an outlet into the airflow under test.
A threaded retaining ring and a one-piece metal socket replace the upper and lower shrouds. The heater stem passes through the center of the ring, which threads into the socket and clamps the heater flange against an internal shoulder. After tightening, the coating runs continuously from the protruding heater onto the exposed face of the ring, bridging the annular junction. The socket fastens to the device body and carries the heater leads through its rear opening.
Three 2 mm diameter heater pins protrude 10 mm from a common base, with their centers on an equilateral triangle of 5 mm side length. The upper and lower shrouds capture the three pin flanges in individual recesses. The coating bridges each pin-to-base junction and covers the base surface between the pins. Each pin has a separate electrical circuit so the controller can regulate heating in three regions of the same precursor bed.
A peristaltic pump connects a liquid reservoir to a capillary nozzle positioned beside the protruding heater tip. The upper and lower shrouds capture the heater flange, and a continuous coating covers the heater-to-base junction. A temperature sensor near the tip enables the pump after the heater reaches its operating temperature. Pump rotation meters liquid onto the coated tip, and a fan carries the generated aerosol into an outlet duct.
A differential pressure sensor measures the pressure drop across a calibrated restriction in the device inlet. Downstream, the upper and lower shrouds capture the heater flange, and the coating bridges the junction between the protruding heater and the base. The controller converts the pressure drop to airflow using a stored calibration table and sets a heater power command from an airflow-to-power map. A temperature sensor near the heater tip supplies feedback that reduces power when the tip reaches its temperature limit.
An inspection fixture holds the assembled heater by its lower shroud and supplies current through the heater leads. A diffuse light ring illuminates the coated junction while a camera records the full circumference as the fixture rotates. The controller heats and cools the assembly through a programmed cycle and compares images taken at the same temperature before and after cycling. Image analysis flags newly formed line discontinuities across the coated junction for inspection.
Two stainless steel rails carry a ceramic heater mount and a removable precursor holder. A perforated guard on ceramic spacers limits contact with the hot assembly, and a short outlet tube carries aerosol from the holder.
Two stamped aluminum half-shells form the device body and fasten to a molded internal frame. Guide rails on the frame align the heater assembly with the precursor insertion opening.
A resistive track embedded in a laminated alumina blade heats the precursor along the projecting portion of the blade. A metallized band on the blade shank forms a brazed joint with a nickel alloy flange that seats in the base.
An alumina film deposited by atomic layer deposition follows the contour of the exposed heater and the adjacent ceramic base. The film continues over the flush heater-to-base seam and terminates on the base beyond the seam.
An annular shoulder in the lower shroud supports the heater flange. The upper shroud screws onto the lower shroud, and an inward lip traps the flange against the shoulder.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Aerosol delivery devices of the present disclosure generally include a number of components provided within an outer body or shell, which may be referred to as a housing.A · US 10,080,387 B2 · ¶ 42
Referring to FIG. 2, the aerosol delivery device 10 further includes a vaporizing unit 300 configured to removably engage the open end 202 of the reservoir 200. The vaporizing unit 300 includes a liquid transport element 306 and a heating element 308 (shown in FIG. 4A and FIG. 4B) and may include an outer shell 301.A · US 10,080,387 B2 · ¶ 52
It is known to provide a steering column for a vehicle in which a steering column shaft is supported within a telescopic shroud that is fixed to the body of the vehicle, usually to a beam located behind the dashboard. The steering column shaft protrudes from one end of the shroud and is connected to a steering wheel that the driver can turn to rotate the shaft and hence steer the vehicle.B · US 10,137,923 B2 · ¶ 3
In a clamp state as shown in FIG. 2(b) the slot in the outer shroud portion is closed up causing the inner diameter to reduce and the lower shroud portion to clamp onto the upper shroud portion. This removes any free play and prevents accidental movement of the upper shroud portion.B · US 10,137,923 B2 · ¶ 47
An empty cell means only that no passage was reproduced there.
However, certain other form factors for aerosol delivery devices and other aerosol precursor composition storage arrangements may be desirable.A · US 10,080,387 B2 · ¶ 3
The present disclosure relates to materials and combinations thereof useful in aerosol delivery devices (e.g., electronic smoking articles) and like personal devices.A · US 10,080,387 B2 · ¶ 4
If the force was not released the controlled movement of the upper shroud portion into the lower shroud portion would be inhibited by the clamp force.B · US 10,137,923 B2 · ¶ 11
The invention provides a means for removing, or substantially reducing, at the initiation of column collapse in crash, the tube-to-tube friction which is present due to the operation the clamping lever and cam mechanism.B · US 10,137,923 B2 · ¶ 11
patent.fyi, US 2026/0354475 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354475/, SHA-256 7729d45f2983e5d24951255525c9aca1fa2a512f0434a8762753d2272537daee