1.1Stamped stainless steel casing
A deep-drawn steel shell encloses a glass-filled polyamide insert that locates the cap on the device body. The rolled rim of the shell captures the insert and covers the cut sheet edge.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A deep-drawn steel shell encloses a glass-filled polyamide insert that locates the cap on the device body. The rolled rim of the shell captures the insert and covers the cut sheet edge.
A machined shoulder in the aluminum shell seats a silicone ring that grips the device neck. An external anodic oxide layer provides a wear surface for handling.
An injection-molded polyamide shell uses axial ribs to resist inward deflection when the cap is squeezed. A stainless steel spring clip captured in an internal groove engages a lip on the device body.
Ceramic injection molding forms a zirconia shell that is debound and sintered to final density. A silicone sleeve lines the shell, cushions the ceramic rim, and provides a friction fit on the device neck.
A spun titanium shell has a rolled edge that captures a polyether ether ketone carrier. Two opposed lugs on the carrier engage slots on the device neck when the cap turns.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A polyphenylene oxide outer casing fits over the front of a waterborne paint sprayer. A central opening clears the spray nozzle, and opposed tabs engage slots in a collar on the sprayer body. The operator twists the casing to release the tabs and removes it to wipe paint deposits from the nozzle area.
The cap uses an injection-molded polyamide 66 outer casing containing 30 percent short glass fiber by mass in place of polyphenylene oxide. A metal base flange fastens to the casing with three screws seated in molded bosses. The flange bears against the device body when the cap is seated and transfers axial loads from the casing to the body.
A cylindrical polyphenylene oxide casing has a 24 mm outside diameter and a 1.2 mm nominal wall thickness. The wall thickens inward to 2.0 mm over the final 4 mm of the open end, with a 1 mm radius at the transition. The thickened rim seats around a matching shoulder on the device body and spreads the load from squeezing the open end during removal.
A polyphenylene oxide outer casing carries two recessed metal pads connected to a battery charging circuit through spring contacts at the cap-to-body interface. A molded groove in the casing mates with a rib in a charging cradle and aligns the pads with the cradle pins. Seating the device in the cradle closes the charging circuit while the cap stays installed.
A small permanent magnet sits in a blind pocket at the rim of the polyphenylene oxide outer casing. A Hall-effect sensor on the device circuit board faces the magnet when the cap reaches its seated position. A controller samples the sensor every 20 ms and enables the heater only after five consecutive seated readings. A single unseated reading disables the heater.
A rotary fixture holds each molded polyphenylene oxide outer casing with its seating rim perpendicular to a camera fitted with a telecentric lens. A backlight produces a silhouette, and the fixture presents the casing at four orientations spaced 90 degrees apart. Inspection software measures the rim diameter and checks the seating profile against the drawing tolerances. A conveyor diverter routes casings with out-of-tolerance measurements to a separate bin.
An injection-molded blend of polyphenylene oxide and high-impact polystyrene forms the outer casing. Molded tabs engage recesses in an inner cap liner, and an annular shoulder sets the liner depth.
The outer casing uses a polyphenylene oxide and polystyrene blend compounded with 20 percent short glass fiber by mass. Molded bosses receive thread-forming screws that secure a separate latch carrier.
A polyphenylene oxide blend is injection molded around two knurled brass inserts. The inserts anchor screws that retain a stainless steel bracket carrying the cap latch.
A rigid shell molded from a polyphenylene oxide blend forms the structural wall of the outer casing. Silicone overmolding fills undercut pockets in the shell and forms raised grip pads on its exterior.
patent.fyi, US 2026/0354476 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354476/, SHA-256 6c454aa90710584c203a785a6ea54f43242e7ff2525d3750c7b49f217e400a0c