1.1Open frame with local guards
The rails hold the end plates at a fixed spacing, and the plates locate the heater assembly and mouthpiece. Spaced ceramic guard ribs keep fingers clear of the heated assembly, and a separate duct carries the airflow.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The rails hold the end plates at a fixed spacing, and the plates locate the heater assembly and mouthpiece. Spaced ceramic guard ribs keep fingers clear of the heated assembly, and a separate duct carries the airflow.
Each bracket attaches to a boss inside the housing and carries two ceramic pads that engage tabs on the heater segment. One bracket fixes the axial position, and slots in the other let the tabs slide as the segment expands.
Two flat ceramic plates carry resistive traces and meet two ceramic side rails to form a rectangular channel. A matching rectangular plug of smokable material slides into the channel, and the plates heat its two broad faces by contact.
A rectangular guide holds a plug of smokable material while a tapered ceramic blade enters a slot in the plug. A resistive trace on the blade transfers heat through a ceramic coating into the material on both sides of the blade.
A resistive foil band bonded to the exterior of a thin aluminum nitride sleeve transfers heat through the sleeve wall. The smokable material sits in the bore and receives heat by contact with the inner wall.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A benchtop sample conditioner uses a cylindrical resistive heater inside a support sleeve within a metal enclosure. Ceramic blocks fastened to the sleeve engage flats on the heater's outer barrel and carry the heater. A glass vial slides into the heater bore, where a timed heating cycle releases volatile compounds from a dried plant sample into the vial headspace for sampling through the cap.
A glass fiber reinforced polyimide tube replaces the heater support sleeve inside the outer housing. Rectangular windows in the tube receive ceramic keys that engage matching pockets on the heater barrel. The keys carry the annular heater and transfer insertion loads into the tube, while the heater bore receives the smokable material.
Three stainless steel leaf springs with ceramic shoes replace the mechanical isolators inside the support sleeve. The springs attach to the sleeve at 120 degree intervals and press their shoes into shallow pockets on the heater barrel. The pocket shoulders carry axial loads during material insertion, and the springs deflect radially as the barrel expands during heating.
Three cylindrical heater segments share an 8 mm bore and have axial lengths of 6, 10 and 14 mm. Ceramic saddle blocks fixed to a common support sleeve engage grooves on the outside of each segment. Each segment carries a separate resistive winding, and the controller energizes the 6 mm segment at startup, the 10 mm segment after 5 seconds and the 14 mm segment after 10 seconds.
A rechargeable handheld unit combines the sleeve-mounted cylindrical heater with a drop-in charging cradle. Ceramic bosses on the sleeve engage recesses in the heater barrel, and the sleeve locates in the upper half of the housing. Spring contacts in the cradle mate with pads on the housing base and feed a battery charging circuit. A cradle detection contact disables the heater driver while the unit is seated.
A cylindrical heater sits inside the support sleeve on ceramic blocks that engage the outside of the heater barrel. Two pressure taps straddle a calibrated restriction in the inlet duct upstream of the heater bore and connect to a differential pressure sensor. A controller converts the pressure difference to airflow using a stored calibration table and increases heater duty cycle as airflow rises. A temperature sensor bonded to the barrel supplies feedback for regulating heater temperature during the draw.
Two injection-molded glass-filled polyamide shells meet along a longitudinal seam and attach through recessed screw bosses. Molded ribs locate the heater support sleeve and maintain an air gap between the sleeve and the outer wall.
A sintered alumina tube fits within the outer housing. An internal shoulder seats the lower heater mount, and three recesses at the opposite end locate the upper mount.
A thick-film resistive trace wraps around the exterior of a hollow alumina cylinder and terminates at two contact pads. The cylinder receives a matching plug of smokable material in its bore and conducts heat through its wall into the plug.
Three steatite buttons spaced 120 degrees apart at each end center the heater segment within the sleeve and limit heat conduction through the mounts. A groove at one end retains its set of buttons axially, and an elongated seat at the other end lets the heater expand lengthwise.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The PM filter assembly 34 includes a housing 200, a filter 202, and the zoned heater 35.B · US 2009/0113883 A1 · ¶ 53
A flange bracket 36 includes an axial sleeve portion 38 co-axially surrounding the radial isolator bushing 16 such that the axial portion 20a of the outer sleeve 20 of the radial isolator bushing 16 is in close proximity to the axial portion 38 of the flange bracket 36.A · US 7,389,977 B1 · ¶ 14
The resistive heater 200 may comprise one or more coils, heater segments, or conductive elements that cover the respective zone to provide sufficient heating. The resistive heater 200, as shown, includes three (3) heater segments 201, which are electrically conductive.B · US 2009/0113883 A1 · ¶ 52
A gap is defined between the inner sleeve 18 and the outer sleeve 20 of the radial isolator bushing 16 and an elastomeric isolation member 22 is molded within the gap between the inner sleeve 18 and the outer sleeve 20.A · US 7,389,977 B1 · ¶ 12
An empty cell means only that no passage was reproduced there.
A body mount joint must isolate the vibration from the frame to the body or vice versa.A · US 7,389,977 B1 · ¶ 3
The present disclosure provides a body mount assembly for reducing vibration between a vehicle body and a frame.A · US 7,389,977 B1 · ¶ 4
However, durability of the electrically heated PM reduction systems has been difficult to achieve.B · US 2009/0113883 A1 · ¶ 8
Also, power to electrically heat the PM can be significant.B · US 2009/0113883 A1 · ¶ 8
patent.fyi, US 2026/0354478 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354478/, SHA-256 8f14276a00ab51c28a98e5bc5c962b6b3a255edf545f48e664cb8dcbda66aa84