1.1Side loading tobacco chamber
A ceramic heater beneath the chamber heats the tobacco through a stainless steel floor. Air enters through ports in the side wall, passes over the tobacco, and carries aerosol to the mouthpiece.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A ceramic heater beneath the chamber heats the tobacco through a stainless steel floor. Air enters through ports in the side wall, passes over the tobacco, and carries aerosol to the mouthpiece.
A ramp on the holder pushes a spring-loaded pawl aside during insertion. The pawl snaps into a recess at full insertion, and a release button retracts it for removal.
A switching circuit drives a transmitter coil behind the cradle wall. A receiver coil in the holder feeds a rectifier and a charge controller that supply direct current to the holder battery.
The holder seats against a fixed stop with the insertion hole aligned to a window in the cradle. A cover slides along two parallel rails to close or clear the window, and a spring detent holds the cover at each end of travel.
A sealed momentary switch signals the controller to energize the heater and illuminate a status light. Releasing the button ends the cycle, and a timer cuts heater power after five seconds if the button stays pressed.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A respirator training handpiece tilts in a powered magnetic cradle that covers its mouthpiece in the stored position. With the mouthpiece exposed, a differential pressure sensor measures inhalation across a fixed flow restriction in the handpiece. The controller counts each draw that meets a preset duration and flow target, sends a short tone after each accepted draw, and changes to a two-tone signal when fewer than three draws remain in the exercise.
A stainless steel leaf spring inside the cradle replaces magnetic retention. A rounded boss on the spring snaps into a groove in the holder's pivot collar, and two detents on the collar index the covered and exposed positions. The user presses an external release tab to lift the boss clear of the groove, while spring-loaded cradle contacts supply power through arcuate pads during tilting.
A planar transmitter coil in the cradle replaces the exposed power terminal, and a receiver coil sits behind the facing wall of the holder. Both coils are centered on the tilt axis with their winding planes perpendicular to that axis, so the coil spacing stays fixed as the holder tilts. A rectifier and charge controller in the holder convert the received power to direct current for the holder battery.
A pivot pin and spring plunger index the holder at 0, 35, and 65 degrees relative to its stored position. At 0 degrees the cradle covers the insertion opening, and at 35 degrees the opening clears the cradle for normal use. At 65 degrees a removable stop collar around the opening clears the cradle lip for cleaning, and a cam-operated switch disables the heater.
Four magnetic tilt cradles mount on a charging rack with a common direct-current supply and an independently switched power channel for each bay. Each bay supplies its holder through spring contacts and measures channel current with a shunt resistor. The rack controller alternates power between pairs of occupied bays in five-minute intervals, while each holder uses its own puff sensor and controller to select its feedback mode.
A differential pressure sensor connects to the airflow passage through taps on either side of a fixed restriction, and the holder controller samples it at 100 samples per second. Software tracks the zero-flow baseline between draws and freezes it when the pressure drop crosses the onset threshold. The controller counts an event when the drop stays above the onset threshold for at least 150 milliseconds and then falls below a lower release threshold. An acoustic transducer emits one pulse after each counted draw and a fixed pair of pulses when the remaining count falls below three.
An injection-molded cradle shell forms a cavity with two longitudinal ribs that guide the holder during insertion. A molded ledge at the base sets the insertion depth.
Two permanent magnets sit in recesses in the cradle wall. Matching low-carbon steel inserts in the holder align with the magnets at full insertion and increase the force required to remove the holder.
Two spring-loaded pins in the cradle press against gold-plated pads on the holder when it reaches its seated position. One pin supplies positive direct-current power to the charging circuit, and the other provides the return path.
A vibration motor gives one short pulse at the start of a session. The controller subtracts one from the remaining puff count for each detected puff and switches to two short pulses when the count drops below three.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The cigarette holder converter assembly A is locked by the neck when the cigarette holder converter assembly A is inserted into the e-liquid storage assembly D to a target position.B · US 2017/0013881 A1 · ¶ 18
Inside one holder 222 is disposed a non-slip (rubber) friction member 226, and the other holder 224 is formed in such a shape as covers the cradle connector 230. The sliding member 220, as it is formed of plastic, can be elastically deformed when the digital camera 10 is mounted, so that the pair of holders 222 and 224 can hold the digital camera 10 and at the same time the friction member 226 can secure a required holding force.A · US 7,167,207 B2 · ¶ 60
The cradle connector can comprise communication terminals for two-way communication with the external device and power terminals for supplying power to the camera, and can further comprise audio/visual terminals for receiving audio/visual signals from the camera and outputting the audio/visual signals to the external device.A · US 7,167,207 B2 · ¶ 21
When the cigarette holder converter assembly A is inserted into the e-liquid storage assembly D to a target position, the cigarette holder converter assembly A is adapted to rotate to regulate a gas flow via a top part of the cigarette holder.B · US 2017/0013881 A1 · ¶ 18
An empty cell means only that no passage was reproduced there.
However, a cradle apparatus having a cradle connector on the bottom face of the camera mount as mentioned above may allow the camera to be inserted obliquely into the camera mount, and the resultant prying might damage the connector.A · US 7,167,207 B2 · ¶ 6
The present invention, attempted in view of these problems, is intended to provide a cradle apparatus for a camera facilitating satisfactory connection between connectors, ready locking of the camera in a state in which the connectors are connected, and minimization of the dustiness of the cradle connector.A · US 7,167,207 B2 · ¶ 9
As a result, it is difficult for the e-liquid to fully contact the heating wire, the combustion of the e-liquid is incomplete at times and at other times the e-liquid is over burned, the produced smoke volume is relatively small, and the flow of smoke is slow, all of which adversely affects the taste of the smoke.B · US 2017/0013881 A1 · ¶ 5
The improved electronic cigarette is adapted to produce large smoke volume without the production of scorched smell.B · US 2017/0013881 A1 · ¶ 6
patent.fyi, US 2026/0354479 A1, claim 1, first published 2026-11-18T23:03:08-05:00, https://patent.fyi/US20260354479/, SHA-256 c7aafc7e095553ba161dfbdb6429a49061255d05d42a5b89914e757c73fcc373