1.1Open frame with heat shield
Two glass-filled polymer rails support the heater assembly, circuit board, and battery module. A ceramic shield between the heater and the grip limits heat transfer, and the spaces between the rails remain open.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two glass-filled polymer rails support the heater assembly, circuit board, and battery module. A ceramic shield between the heater and the grip limits heat transfer, and the spaces between the rails remain open.
A regulated battery pack supplies direct current through a locking two-conductor connector. The controller switches power from the input connector to the heater, and the pack monitors its own charge.
A momentary switch rated for the heater current completes the battery-to-heater circuit through a bimetal temperature switch. Releasing the button opens the power circuit, and the bimetal switch also opens it at a fixed temperature. The charge-monitoring controller reads battery voltage through a separate sensing branch.
The controller transmits the measured charge level over a short-range radio link. A separately powered receiver converts the reported value to a percentage and renders it on a segmented liquid-crystal display.
A battery monitor samples terminal voltage and current and integrates their product over time to track energy entering and leaving the battery. The controller updates the remaining energy estimate from this record and displays it in watt-hours.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handheld bag sealer encloses a rechargeable battery and a controller and carries a resistive heating strip in one jaw. A switch at the hinge starts a timed seal cycle when the jaws close. The controller subtracts the energy reserved for low-voltage cutoff from the estimated battery energy, divides the result by the calibrated energy per seal, and rounds down. A display set into the handle shows the remaining seal count.
A reflective segmented liquid crystal module replaces an emissive display in the outer housing. The module sits behind a clear window and connects to the controller through a segment driver. The controller converts the battery gauge reading to an integer percentage of full-charge capacity and sends the corresponding digit and percent-symbol patterns to the driver. The driver applies alternating voltages to the selected segments.
The controller supports heating profiles with a 120-second hold or a 240-second hold following preheat. A selector on the housing sets the active profile, and a temperature sensor supplies feedback as the controller regulates heater power. The controller stores a separate energy budget for each profile that includes preheat and the hold period. On profile selection, the housing display shows the whole number of sessions supported by the usable battery energy and the selected budget.
A tabletop charging dock mates with recessed power and data contacts on the device housing. While docked, the device controller sends the current session count over a serial data connection once per second. The dock uses its own display to show the count as charging progresses. The device display shows the current count after removal from the dock.
A current-sense resistor sits in series with the heater branch, and the controller samples branch current and supply voltage throughout each heating session. The controller integrates the product of voltage and current over time to calculate the energy used. It updates a running average from completed sessions and stores the average in nonvolatile memory. The controller divides the usable battery energy by the stored average and displays the whole-number result.
A thermistor attached to the battery supplies cell temperature to the controller. The controller measures battery voltage and current just before and during heater startup and divides the voltage drop by the current increase to estimate battery resistance. It combines that resistance with a stored voltage table indexed by charge level and temperature to estimate loaded voltage at successive charge levels. The display shows the number of complete sessions supported by the estimated energy available before the loaded voltage reaches the cutoff threshold.
Two injection-molded polycarbonate halves form the outer housing. Molded ribs position the internal assemblies, and screws engage brass inserts to join the halves.
A cylindrical lithium-ion cell sits in a molded cradle inside the outer housing. Welded nickel tabs connect the cell terminals to a protection board that interrupts current during overcurrent or undervoltage.
A resistive film on an alumina sleeve heats a unit of aerosol generating material held inside the sleeve. The controller reads a temperature sensor on the sleeve and adjusts the duty cycle of a transistor that switches heater current.
A charge monitor integrates current through a shunt resistor to estimate the charge remaining in the battery. The controller divides that estimate by the stored full-charge capacity, multiplies by 100, and displays the result as a whole-number percentage.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Certain embodiments include a hard external shell in the general conformation of the electronic device.A · US 2013/0292288 A1 · abstract
The aerosol-generating system comprises a power supply, typically a battery, for example within the main body of the housing.B · US 2018/0146709 A1 · ¶ 63
The temperature of the heating element may be controlled by electric circuitry 2 (e.g., the controller 400). Once a negative pressure has been detected and the heater and/or the tube element of the vaporizer has reached the operating temperature, the electric circuitry 2 may activate the micropump 5 and set a determined flow rate for delivering liquid aerosol-forming substrate to the inner volume of the tube element of the vaporizer for the duration of the negative pressure.B · US 2018/0146709 A1 · ¶ 76
As illustrated, gasket 250 is disposed around a perimeter of display window 128 such that a display window of electronic device 104 directly provides an area effective to resist water entry into shell 102.A · US 2013/0292288 A1 · ¶ 63
An empty cell means only that no passage was reproduced there.
There are many commercially available housings structured to provide add-on protection for certain of such electronic devices, yet none have sufficiently addressed the need for impact protection.A · US 2013/0292288 A1 · ¶ 4
The invention may be embodied to provide an add-on enclosure to increase ruggedness of a commercially available portable electronic device.A · US 2013/0292288 A1 · ¶ 6
A problem often observed in these aerosol generating systems is leakage of liquid from them, which can be inconvenient if they are carried in a pocket of the trousers of an adult vaper.B · US 2018/0146709 A1 · ¶ 4
Hence, it would be desirable to have a vaporizer for an aerosol-generating system and a vaporizing method that provide sufficient vaporization of a liquid aerosol-forming substrate and are capable of avoiding an amount of liquid drips from the heater.B · US 2018/0146709 A1 · ¶ 5
patent.fyi, US 2026/0354488 A1, claim 1, first published 2026-11-18T23:36:45-05:00, https://patent.fyi/US20260354488/, SHA-256 2ee7a63cfe8fb3fc7c2712c40ead10c7ebdb6e8e8a0d9a3bd4e7e5ac3b1bcdae