1.1Flat cassette in keyed chamber
Guide rails locate the cassette with one broad face against a planar heater. A mark on a narrow edge faces the optical sensor when the cassette reaches the chamber stop.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Guide rails locate the cassette with one broad face against a planar heater. A mark on a narrow edge faces the optical sensor when the cassette reaches the chamber stop.
An axial stop positions the marked end face at a fixed distance from a reader beyond the chamber end. An annular passage around the stop supplies air to the article.
Two circumferential bands with assigned magnetic polarities encode the article type. A Hall sensor outside a nonmagnetic chamber wall samples the bands as the rod moves past it during insertion.
The sensor and its illumination diode face an angled window in a chamber collar. A chamber stop aligns the side mark with the oblique optical path at full insertion.
The indicia encode a temperature setpoint and a hold time as numeric fields. The controller checks both values against operating limits and uses them to regulate the heater through temperature feedback.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A bench calibration fixture accepts a cylindrical cartridge containing a reference volatile compound in a porous carrier. A side-facing optical reader views a dot code on the cartridge through a removable sapphire window. The controller uses the code to select the heater ramp and hold time for the compound. A regulated carrier gas stream carries the released vapor from the chamber to the gas sensor under test.
Axially spaced rings of magnetic composite in the rod wrapper replace the optical marking, and a matching row of Hall-effect sensors replaces the optical reader. An insertion stop aligns the rings with their respective sensors, and a replaceable alumina shield sits between the chamber and the sensor board. The controller samples each position for ring presence and maps the resulting bit pattern to a heater profile.
Five optical readers sit at 72° intervals around the chamber, each behind a removable fused silica window. Each reader images a 90° sector of the seated rod, and a mechanical stop aligns the axial center of the side code with the readers. The controller registers the overlapping images to reconstruct the circumference and decodes the mark at any insertion angle. A lookup table maps the decoded identifier to a heater profile.
A differential pressure sensor connects across a fixed restriction in the intake air path. The optical reader identifies the seated rod through a replaceable window, and the controller loads the temperature target and maximum pulse duration for that rod type. A sustained pressure drop above the configured threshold starts the heating pulse. The pulse ends when the pressure drop falls below a lower threshold or the loaded duration expires.
A fixed reference target sits opposite the side-facing optical reader and is visible through the removable window when the chamber is empty. Before insertion, the controller records the target with the illumination off and on, subtracts the dark reading, and compares the result with a clean-window baseline. It uses the resulting transmission estimate to normalize the side-code image after insertion. The controller enables the corresponding heater profile after a valid decode and requests window replacement if the reference signal falls below a stored minimum.
The optical reader reads the rod identifier through a replaceable window, and the controller loads a table of heating profiles for that identifier. A thin-film temperature sensor bonded to the heater records the temperature rise during a fixed low-energy test pulse. The controller divides the temperature rise by the delivered pulse energy and selects a profile using stored response bands for that rod type. A feedback loop regulates heater power against the selected temperature trajectory.
A cylindrical chamber receives a 7 mm diameter rod and uses an end stop to register its insertion depth. Circumferential bands printed on the wrapper encode the article type and remain readable at any rotational position.
An 850 nm light-emitting diode and a linear photodiode array face the rod along a radial optical path. A lens images the side bands onto the array across a 3 mm gap between the reader face and the rod surface.
The controller decodes the optical pattern and selects a stored temperature profile for the identified article type. One profile ramps to 230°C and holds that setpoint, while the other ramps to 250°C and then steps down to 220°C. A thermistor provides feedback for heater power control.
A threaded retaining ring seats a fused quartz disk between the optical sensor and the chamber. The disk transmits 850 nm illumination and has a melting temperature above 200°C. Removing the ring releases the disk for replacement.
patent.fyi, US 2026/0354493 A1, claim 1, first published 2026-11-18T23:36:45-05:00, https://patent.fyi/US20260354493/, SHA-256 a7921897c4acc069e580e3272cad9c41c0621c7b648170443c36c1ef45458cb3