1.1Printed graphic on solid brim
A heat press transfers a pigment graphic to the woven polyester facing. A continuous polyethylene stiffener beneath the facing supports the brim across the printed area.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A heat press transfers a pigment graphic to the woven polyester facing. A continuous polyethylene stiffener beneath the facing supports the brim across the printed area.
Matched dies heat-form a shallow relief in a polypropylene brim shell. The shell cools in the dies to retain the raised profile, and a matte finish makes the profile visible in reflected light.
A folded polyester binding strip wraps over the cut edges of the upper facing, stiffener and lower facing. A lockstitch through both legs of the binding secures the strip and holds the layers together.
An annular heated die presses thermoplastic-coated polyester facings together around a matching cutout in the stiffener. After the seam cools, a punch cuts the opening inside the sealed band, leaving a continuous fused margin.
A mold pin defines the opening while molten thermoplastic elastomer fills a channel around the cut edge. The elastomer flows through small holes in the brim stiffener and solidifies into anchors that retain the bead.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A cap for theater rigging crews has a small sight opening near the forward edge of an opaque brim. A matte upper clip follows the rear half of the opening and seats in two blind pockets molded into the top of the brim. The wearer looks through the opening to check overhead rigging with a slight upward glance.
A molded silicone rubber ring replaces the upper clip in a one-piece thermoplastic brim. The ring sits in a shallow recess around the top edge of the opening, and a silicone-compatible adhesive bonds it to the recess floor. The inner edge of the ring has a rounded profile that covers the exposed upper corner of the brim.
Three slots measuring 24 mm long and 5 mm wide run side by side across a 3 mm thick molded brim, with their long axes running front to back. Each slot has semicircular ends, and neighboring slots are separated by 8 mm of solid brim. A separate upper clip follows one semicircular end of each slot and presses into two blind sockets beside that end.
An upper clip surrounds a rectangular brim opening and carries two parallel rails that extend beyond its forward edge. A flat opaque shutter rides in the rails above the brim and has a raised tab for thumb operation. Stops hold the shutter over the opening at one end of travel and retain it clear of the opening at the other end.
An upper clip frames a ventilation opening and incorporates a recessed ledge around its inner edge. A woven polyester mesh spans the opening and is heat staked to posts on the ledge before the clip is installed. Separate pins beneath the clip seat in blind sockets in the molded brim, and the mesh passes air while intercepting insects and coarse debris.
A fixture holds the brim beneath a calibrated overhead camera, and a diffuse backlight reveals the perimeter of the opening. Software fits the detected perimeter to a stored outline and sends the position and rotation to a robotic gripper. The gripper aligns the upper clip with the opening and presses its pins into blind sockets, while a force sensor verifies that the insertion falls within the force and travel limits set for the assembly.
A steel rule die cuts a rounded slot through an upper fabric facing, a polyethylene stiffener and a lower fabric facing in one stroke. The cut edge of the upper facing defines the upper layer perimeter.
A molded nylon upper ring has a flange that overlaps the full upper perimeter. Posts on the upper ring pass through holes alongside the opening and snap into sockets in a lower ring.
A formed stainless steel strip has a U-shaped cross section and follows one straight side of the opening. Its upper leg covers that segment of the upper perimeter while its lower leg presses against the underside of the brim.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Such removable brims may have an inner perimeter smaller than an outer perimeter of the cap's crown to achieve desired higher positioning.B · US 2017/0055618 A1 · ¶ 4
In order to accommodate mount 380, clip 370 defines a hole 385 formed through an upper leg 386 of clip 370. An opposed lower leg 387 is integrally attached to upper leg 386, so as to define a space 388 sized to accept and intimately engage brim 30.A · US 2015/0157078 A1 · ¶ 128
An empty cell means only that no passage was reproduced there.
Requiring at least one hand to hold and point the smartphone or camcorder can be problematic when the smartphone or camcorder is used to record objects and events.A · US 2015/0157078 A1 · ¶ 8
Therefore, it is desirable that video and audio devices, such as smartphones and camcorders, be operable by the user in a manner that avoids the considerations mentioned hereinabove.A · US 2015/0157078 A1 · ¶ 10
Example apparatuses include or are useable with caps that have a top crown that generally surrounds the head, and example apparatuses include an extension, like a brim, from the top crown.B · US 2017/0055618 A1 · ¶ 4
Extensions in example embodiments are above a bottom vertical portion of the crown; that is, the crown extends vertically below the brim so the brim blocks or reflects ultraviolet radiation without interfering with the ears, face, and/or adjustment strap of the cap.B · US 2017/0055618 A1 · ¶ 4
patent.fyi, US 2026/0354517 A1, claim 1, first published 2026-11-18T23:36:45-05:00, https://patent.fyi/US20260354517/, SHA-256 113e717b95236042d820e303da5f7b71a000e44fc244396d5bc2b99667d96b1c