1.2Integral foot contact surface
A single molded foam base forms the heel cup, footbed contour, and ground-contact tread. Rounded ribs on the upper surface compress under load and provide grip against the foot.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A single molded foam base forms the heel cup, footbed contour, and ground-contact tread. Rounded ribs on the upper surface compress under load and provide grip against the foot.
The sleeve wraps around the forefoot and instep, and its lower perimeter bonds to the base. Elastic yarn stretches during entry and contracts around the foot to hold it against the footbed.
Both strap ends attach to reinforced side panels on the bootie. The bootie wraps beneath the foot and carries the strap load, while a contoured recess in the base limits lateral movement of the bootie during stance.
A low-profile air bladder sits in a textile pocket sewn onto the top face of the insert. A squeeze bulb adds air through a check valve to raise the bladder under the arch, and a vent button lets air out to lower it.
A ladder buckle shortens the strap as it runs between two anchors at the rear of the base and around the heel. The strap limits rearward foot movement, and a padded vamp fixed to the base limits upward movement at the instep.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fitting station uses an open sandal with a sole insert seated in a rigid base and a strap spanning the top and sides of the foot. A lead screw in the base lifts a guided plate beneath the arch region of the insert. A threaded anchor draws one end of the strap downward to set tension. The operator records both settings from scales on the adjusters after the wearer stands on the sandal.
A sealed hydraulic bellows replaces the mechanical lift beneath the arch region of the sole insert. The bellows sits in a base recess and raises a guided plate that bears against the insert. A side-mounted screw piston transfers silicone oil between its cylinder and the bellows to raise or lower the plate. A separate rotary adjuster sets tension in the strap across the top and sides of the foot.
A rack and pinion replaces the cord mechanism for adjusting support height. The vertical rack attaches to an arch plate beneath the sole insert and slides in guides formed in the base. A side dial turns a worm that drives the pinion shaft, and a spring-loaded pawl holds the dial at the selected position. A separate threaded strap anchor adjusts tension across the top and sides of the foot.
A transverse shaft in the base carries a five-position stepped cam beneath a guided arch plate. The cam sets the plate at 0, 2, 4, 6, or 8 mm above its lowest position, and a spring-loaded pin engages a recess at each setting. The sole insert rests on the plate in the arch region and on the base at the heel and forefoot. A separate screw-driven anchor sets tension in the instep strap.
The sandal base mounts to a removable rocker outsole through a longitudinal dovetail and a captive heel fastener. The rocker outsole has a curved ground-contact surface that shifts contact from heel to toe as the wearer steps. A side-access screw moves a wedge beneath the arch plate to set support height under the sole insert. A separate side-mounted ratchet tensions the strap across the top and sides of the foot.
A pressure sensor sits beneath the arch region of the sole insert, and an inline load cell connects one strap end to its movable anchor. Separate geared motors drive a lead screw beneath the arch plate and a lead screw at the strap anchor. During a standing fitting, a controller moves each actuator in small increments and reads both sensors after each move. It stops when both readings enter their set bands, a travel limit is reached, or the wearer releases the adjustment button.
A compression-molded foam chassis forms a recessed footbed and raised perimeter walls. Rubber tread pads bond to the underside at the heel and forefoot.
A contoured polyurethane foam insert has a flexible molded carrier with tabs at the heel and toe. The tabs snap into recesses in the base and release when the user lifts a pull loop at the heel.
A 25 mm woven strap crosses the instep and feeds through a cam buckle on the outer sidewall. Pulling the free end increases tension across the top and sides of the foot, and lifting the cam releases the strap.
A recessed side dial rotates a stepped cam beneath a vertically guided arch plate. Three detents hold the plate at its lowest position or raise it by 2 mm or 4 mm.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The insole includes a transparent insole board, which has a top portion is configured to fit within the shoe.A · US 2010/0205828 A1 · ¶ 8
The insole includes a transparent insole board, which has a top portion is configured to fit within the shoe. The insole also includes a sock liner sprayed on to at least a portion of the top of the insole board.A · US 2010/0205828 A1 · ¶ 8
The insole 29 or sockliner that is located above the midsole 31 and adjacent (i.e., located nearby or close to, although not necessarily in contact with) a plantar surface or lower surface of the foot to enhance the comfort of footwear 10.B · US 2015/0027004 A1 · ¶ 27
An article of footwear with an impact resistant sole, an adjustable forefoot strap, a reinforced strap mount, and a method of making the same is shown in FIGS. 1-8 and described below.B · US 2015/0027004 A1 · ¶ 20
Those skilled in the art will recognize that while insole board 41 illustrated in FIGS. 10-13 are substantially flat, they could include an arch support (not shown) or a raised wall portion as illustrated for sock liner of FIG. 8 and still fall within the scope of the invention.A · US 2010/0205828 A1 · ¶ 43
The insole 29 or sockliner that is located above the midsole 31 and adjacent (i.e., located nearby or close to, although not necessarily in contact with) a plantar surface or lower surface of the foot to enhance the comfort of footwear 10. The insole can be contoured to match the contours of the wearer's foot including having an arch support.B · US 2015/0027004 A1 · ¶ 27
An empty cell means only that no passage was reproduced there.
The purpose of the transparent portions are for better determining the fit of the shoe; particularly for children.A · US 2010/0205828 A1 · ¶ 2
It would be advantageous to provide, for a shoe having at least one transparent portion in the bottom, an insole having only a portion being transparent.A · US 2010/0205828 A1 · ¶ 4
Despite the benefits of the known articles of footwear, there remains a need for a flexible article of footwear, such as a sandal or the like, that has an impact resistant sole.B · US 2015/0027004 A1 · ¶ 6
The insole is then operably secured to the plate thereby reinforcing the attachment of the strap to the sole.B · US 2015/0027004 A1 · ¶ 7
patent.fyi, US 2026/0354523 A1, claim 1, first published 2026-11-18T23:36:45-05:00, https://patent.fyi/US20260354523/, SHA-256 6c66efbc76c07078ac5eb9b69f14400b8f0973e5f89332aee15458abd3e87bfd