1.1Foam over molded lattice
The upper foam layer spreads plantar loads over the lattice. Integral lattice struts bend under compression and recover on unloading, while a continuous top flange provides a mating face for the foam.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The upper foam layer spreads plantar loads over the lattice. Integral lattice struts bend under compression and recover on unloading, while a continuous top flange provides a mating face for the foam.
Inward lips on a flexible molded frame engage peripheral grooves in the two layers and resist separation. Locating bosses fit into matching recesses to transfer shear, and the contacting foam faces carry compressive loads.
A continuous seam joins the lower edge of the upper to a flexible carrier ring. The ring snaps under the molded sidewall flange and transfers upper tension into the midsole around the perimeter.
A thin coat of reactive polyurethane hot-melt adhesive covers the prepared mating faces. Light fixture pressure holds the layers in contact as the adhesive cools, and moisture curing develops the final bond strength.
A two-part flexible polyurethane adhesive wets the textile bottom and the prepared foam surface. A shaped fixture maintains contact while the adhesive cures at room temperature and forms a flexible bond line.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A hoof boot uses a molded thermoplastic shell with a flexible cuff and two injection-molded foam layers beneath the hoof. The first foam layer is molded against the heated underside of the shell floor, and the second is molded against the reheated underside of the first layer. Both interfaces fuse directly, and the lower mold cavity forms ground-contact lugs in the second layer.
Flexible polyamide 12 replaces the lower foam layer, and the upper foam layer uses a polyether block amide with polyamide 12 hard segments. The first layer is injection foamed with supercritical nitrogen against a polyamide 12 film that forms the bottom surface of the upper. In a second cavity, the freshly foamed polyamide 12 melt contacts the reheated underside of the first layer and forms a direct thermal bond under molding pressure.
The first foam layer has a nominal thickness of 6 mm under the heel and forefoot. The second foam layer tapers from 20 mm at the heel center to 10 mm at the forefoot flex line, with a continuous transition through the midfoot. The second-stage cavity sets the taper while the mold supports the first layer and exposes its underside for direct fusion with the second shot.
A molded outsole carrier contains threaded sockets that open toward the ground for removable traction studs. The carrier sits in the second-stage mold with the socket openings sealed against removable pins and ribbed anchor flanges facing the lower foam cavity. The second foam shot surrounds the flanges and fuses directly to the first foam layer, and the studs screw into the sockets after demolding.
A robot carries the lasted upper between an infrared heating station and the first injection mold, then carries the upper with the first foam layer through the same station before the second shot. An infrared camera measures the exposed bonding surface after each heating pass, and a controller adjusts heater dwell until the measured surface reaches the fusion window established for the material pair. The controller starts each supercritical foam shot after the mold closes and the insert reaches its seated position.
The second-stage mold uses a servo-driven cavity plate and pressure sensors near the heel and forefoot ends of the lower foam cavity. The second shot fills the cavity with the plate in its initial position, placing the gas-laden melt against the heated underside of the first layer. Once both sensor readings reach the calibrated fill threshold and the bond dwell ends, the controller retracts the plate by a programmed stroke to expand the lower foam layer.
A lower-density thermoplastic polyurethane foam forms the foot-side layer, and a higher-density foam of the same polymer family forms the ground-side layer. Broad mating faces distribute compression across the bonded interface.
A knitted upper includes thermoplastic polyurethane yarn exposed at its bottom surface. A hot shot of compatible polyurethane foam softens the exposed yarn at the interface, and the fused interface sets during cooling.
A molded upper foam layer sits in a second cavity with its bottom face exposed. A hot shot of compatible thermoplastic polyurethane softens that face and forms the lower foam layer, creating a direct polymer bond as the interface cools.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In contrast to art traditional approaches, a first layer (e.g. a midsole) is first soled to an upper in a first mold frame and subsequently a second layer (e.g. an outer sole) is soled onto said first layer in a second mold frame.A · US 2022/0273071 A1 · abstract
In contrast to art traditional approaches, a first layer (e.g. a midsole) is first soled to an upper in a first mold frame and subsequently a second layer (e.g. an outer sole) is soled onto said first layer in a second mold frame.A · US 2022/0273071 A1 · abstract
More specifically, the thermal-fusion-bonding part 20S has a six-layer structure in which the protective layer 23, the metal layer 22, the thermal-fusion-bonding layer 21, the thermal-fusion-bonding layer 21, the metal layer 22, and the protective layer 23 are stacked in this order, and the thermal-fusion-bonding layers 21 adjacent to each other are thermal-fusion-bonded to each other.B · US 2023/0131666 A1 · ¶ 70
An empty cell means only that no passage was reproduced there.
The method allows for an increased design flexibility and the inclusion of additional functional or aesthetic features, such as air pockets, undercuts, toe caps or running sole tips previously not possible with direct soling processes.A · US 2022/0273071 A1 · ¶ 1
While direct soling provides a number of advantages there is potential for improvement in relation to the provision of multilayered shoe soles.A · US 2022/0273071 A1 · ¶ 8
Consideration has been given in various ways of a secondary battery including an outer package member having flexibility; however, the secondary battery still remains insufficient in a cyclability characteristic, a swelling characteristic, and an electric resistance characteristic.B · US 2023/0131666 A1 · ¶ 7
The present technology has been made in view of such an issue and to provide a secondary battery that is able to achieve a superior cyclability characteristic, a superior swelling characteristic, and a superior insulating characteristic according to an embodiment.B · US 2023/0131666 A1 · ¶ 8
patent.fyi, US 2026/0354527 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354527/, SHA-256 e10aeb835dcc4116cd4b3ec21322db5c3df0db0cbd4571601d57cc3e53d4ce1f