1.1Solid aluminum curling barrel
A cartridge heater fits into a blind axial bore in the barrel. The aluminum spreads heat from the bore to the cylindrical hair contact surface.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A cartridge heater fits into a blind axial bore in the barrel. The aluminum spreads heat from the bore to the cylindrical hair contact surface.
A copper sleeve fits against the inside of a smooth aluminum barrel. The sleeve conducts heat between adjacent heater footprints and reduces circumferential temperature differences at the hair contact surface.
Two cartridge heaters slide into close-fitting bores beneath each contact surface. Heat passes from the cartridge sheaths through the surrounding metal to the contact surface.
The inline enclosure contains the power supply, controller, sensor inputs, and heater switches. A multiconductor cable carries switched power to the barrel heaters and returns temperature signals from the barrel.
A thermistor in a shallow blind bore measures the barrel temperature just below each contact surface. The controller uses that reading to adjust the duty cycle of the heaters beneath that surface as a group.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A bench fixture grips the holding portion of a tubular mandrel with four metal contact sectors separated by silicone-filled channels. Two resistive foil heaters attach to the inner wall of each sector, and a thermistor bonded beside each heater feeds the controller in the holding portion. The controller adjusts power to each heater independently to soften a thermoplastic strip held around the mandrel by a spring-loaded forming band.
Thin-film platinum resistance sensors replace bead thermistors in the temperature detection circuit. An electrically insulating, thermally conductive adhesive bonds one sensor to the back of each heater on the inner wall of the segmented barrel. A multiplexer in the holding portion connects each sensor to a constant-current measurement circuit, and the controller converts the measured voltage into temperature and adjusts the corresponding heater power.
A barrel with a 32 mm outside diameter and an 80 mm heated length has eight 1 mm wide silicone-filled channels spaced at 45-degree intervals. Each contact sector carries two 35 mm long heaters on its inner wall, with a 4 mm axial gap between them and 3 mm of clearance at each end. The controller samples each heater's temperature at 10 Hz and adjusts each of the 16 heater outputs independently to maintain a 160 °C heater setpoint.
A bearing supports the segmented barrel at the end of the holding portion, and a geared motor turns the barrel and an attached hair clip together. A multichannel slip ring carries a shared heater supply return, separate switched feeds for the heaters, and a digital link to a temperature measurement board that rotates with the barrel. The controller in the holding portion reads each heater temperature over the link and adjusts its power independently while an encoder tracks the barrel angle for winding.
Two foil heaters line the inner wall of each contact sector, and a thermistor bonded to each heater supplies temperature data at 20 Hz. The controller fits a line to the latest ten samples for each heater and adds a power increment proportional to the cooling rate when the fitted slope falls below a negative threshold. The controller caps the increment at 20 percent of rated heater power and ramps it to zero over half a second when the slope becomes nonnegative.
During calibration, a spring-loaded surface probe measures the center of each heater footprint on the outside of the barrel while the controller records the corresponding inner-wall sensor reading. The controller collects paired readings after stabilization at two operating temperatures and stores a separate linear correction for each heater in nonvolatile memory. During operation, the controller applies each correction to its live sensor reading and adjusts the corresponding heater power against a common surface temperature setpoint.
A drawn aluminum tube seats over a glass-filled polymer collar at the end of the handle. Two radial screws engage brass inserts in the collar and hold the tube against an axial shoulder.
Four axial isolation channels spaced 90 degrees apart define four contact surfaces around the tube. Two mica-insulated etched-foil heaters bond to the inner wall beneath each surface and occupy separate positions along the tube.
A power module in the handle provides a 24-volt rail for the heater drive and a 3.3-volt rail for the microcontroller and temperature measurement circuit. The microcontroller reads thermistor divider voltages through analog inputs and sends duty-cycle signals to the heater switching transistors.
A thin-film resistance temperature sensor bonded to each heater supplies a reading to the controller ten times per second. The controller compares each reading with its setpoint and updates the duty cycle of that heater through a dedicated switching transistor.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
FIG. 1 is a side perspective view of the three hair care devices and bottom view of the battery packs of the first exemplary embodiment, displaying the curling iron 10, the blow dryer 11, the straightener 12, the battery packs 13, the curling iron handle 13A, the blow dryer handle 13B, and the curling iron handle 13C.A · US 2015/0157112 A1 · ¶ 8
Specifically, control unit 7 switches between direct supply of a current from power supply portion 8 to heater 52 and supply of a current from power supply portion 8 to heater 52 under PWM control such that a result of detection by temperature detection portion 54 efficiently indicates a target temperature.B · US 10,520,867 B2 · ¶ 31
Specifically, control unit 7 switches between direct supply of a current from power supply portion 8 to heater 52 and supply of a current from power supply portion 8 to heater 52 under PWM control such that a result of detection by temperature detection portion 54 efficiently indicates a target temperature.B · US 10,520,867 B2 · ¶ 31
An empty cell means only that no passage was reproduced there.
However, the power cords on these devices can be very cumbersome and annoying, particularly for those who own and use more than one of these devices.A · US 2015/0157112 A1 · ¶ 5
The user is enabled to move freely while using the devices, without being encumbered by power cords.A · US 2015/0157112 A1 · ¶ 5
The PWM-controlled heater drive circuit, however, requires high-frequency chopping, and hence it is disadvantageous in that a noise filter circuit as measures against noise increases in size and a power loss in a full-wave rectifier circuit and a switching element is caused.B · US 10,520,867 B2 · ¶ 6
One object of the present technique is to provide an image forming apparatus including a heater configured to reduce the drawback of a heater drive circuit.B · US 10,520,867 B2 · ¶ 7
patent.fyi, US 2026/0354549 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354549/, SHA-256 5e1d21c19e38be8b1ffc48a9d001b6e8cb71dcfa22d7c55440ac5fef4aa5a8d8