1.1Continuous oval foil blank
An oval die cuts the blank from aluminum foil. The operator places one rounded end near the roots, lays the hair along the long axis, and folds the other rounded end over the treated length.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An oval die cuts the blank from aluminum foil. The operator places one rounded end near the roots, lays the hair along the long axis, and folds the other rounded end over the treated length.
A rigid paddle supports the foil from underneath while the operator brushes color onto the hair. The operator folds the foil over the hair and slides the paddle out from under the packet.
A shallow groove in a polypropylene rail receives the flat foil margin and positions a raised lip beside it. The lip contains sideways flow during brushing, and the operator lifts the foil margin out of the groove and folds it over the hair.
Two parallel embossed ribs in the same lateral strip stiffen the margin the operator grips during placement. The operator lays hair on the broad smooth area beside the ribs and folds the free margin across the treated section.
A spring clamp with broad, rounded jaws grips the top margin of a uniform aluminum blank and lifts it onto a paddle. The jaws spread the lifting load across the margin, and the operator releases the clamp before placing the hair.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A thin polypropylene sheet has opposing reinforced side portions made from woven polypropylene tapes bonded along its lateral edges. The flexible center wraps around a loose bundle of insulated wires on an assembly bench. The two reinforced portions overlap and receive reusable clips that hold the wrap closed while the bundle moves between workstations.
A clear cast polypropylene film replaces the metal foil sheet body. Narrow strips of open polypropylene mesh are heat bonded to the film along both lateral edges, leaving the center and its hair-contact surface smooth. The mesh limits stretching at the edges during handling, and the center bends around the hair section so the treated strands remain visible through the film.
Two soft aluminum wires supply the side reinforcement in a thin foil sheet. Each lateral edge folds around one wire, and the ends of each hem fold inward to enclose the wire tips. The unwired center conforms around the hair, while the wires retain the transverse bend after the sheet folds over the treated section.
A sheet for short hair sections measures 80 mm wide and 120 mm long. Folded hems extend 6 mm inward from one lateral edge and 14 mm inward from the opposite edge, leaving a 60 mm flexible center. The wider hem provides a gripping surface during placement, and the narrower hem leaves room for an adjacent sheet when the two wraps sit side by side.
A rigid coloring board carries two spring clips on transverse slots so their spacing matches the reinforced side portions of the sheet. Each clip grips a reinforced portion near the top edge, leaving the flexible center clear for the hair section. The board supports the sheet during brushing, then the clips release it so the center folds around the treated hair.
An overhead camera measures the width of a hair section laid on a marked tray, and software adds 10 mm of clearance on each side to set the flexible center width. Two laterally adjustable applicator heads bond reinforcing tape to a continuous foil web at the calculated spacing. Slitting blades trim the web at the outer edges of the tapes, and a crosscut blade separates each sheet.
A die cuts a 100 mm by 250 mm blank from annealed aluminum foil, with two straight lateral edges and parallel top and bottom edges. The operator places the top edge near the roots and folds the bottom edge upward after applying color.
A forming roll turns a 4 mm strip along the first lateral edge inward and presses it flat against the sheet. The resulting two-layer hem increases local bending resistance and encloses the cut edge.
Matched embossing rolls form two shallow longitudinal ribs within an 8 mm band that starts at the second lateral edge. The raised profile stiffens the band against bending along the length of the sheet.
The center consists of a single layer of 15 micrometer annealed aluminum, and a bonded aluminum strip adds a second layer along each side. The single-layer center bends over the hair bundle under finger pressure, while the laminated margins resist bending.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The heatable plates have hair-contactable surfaces which are operable to come into contact with, and apply heat to, hair during use of the hairstyling device.A · US 2023/0292903 A1 · ¶ 3
Moreover, the entire upper and lower hair contact surfaces 234, 252 between the sides 230, 248 are substantially smooth and free of surface features.B · US 2024/0298766 A1 · ¶ 46
An empty cell means only that no passage was reproduced there.
However, the flexibility and/or versatility of known hairstyling devices is limited.A · US 2023/0292903 A1 · ¶ 4
By controlling heating of the hair contact member based on the determined speed of the hair contact member, heat delivery and/or distribution along the tress can be controlled and/or adapted in a more intelligent manner.A · US 2023/0292903 A1 · ¶ 7
In addition, the hair stylers may require the users to hold the hair stylers in awkward orientations when styling the hair and may not accommodate the users' preferred methods for gripping and manipulating the styler because of the orientations of the straight and flat hair contact surfaces relative to the handles.B · US 2024/0298766 A1 · ¶ 3
There is a need, therefore, for a hair styler that can be used for a larger range of styling operations and that is more intuitive for a user to style their hair with as compared to at least some conventional hair straighteners.B · US 2024/0298766 A1 · ¶ 4
patent.fyi, US 2026/0354553 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354553/, SHA-256 710391db6348bf7030b03451d6e5b423c3dd59bfad19f4a6c112a6c046b67b83