1.1Back panel on standoffs
Two bowed aluminum stays hold the back panel approximately 30 mm behind the wearer's back in the fitted position. The stays bear on pads at the shoulders and transfer the lower portion of the load to a padded hip belt.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two bowed aluminum stays hold the back panel approximately 30 mm behind the wearer's back in the fitted position. The stays bear on pads at the shoulders and transfer the lower portion of the load to a padded hip belt.
A curved saddle bolted between two aluminum rails supports the bottom of the container. Two adjustable webbing loops pull the container toward the rails, and a padded hip belt attaches to the lower rail ends.
A single textile bib extends across the sternum and joins the rear panel through shoulder bridges. A side buckle opens the article for dressing and tensions the bib against the torso when closed.
A molded yoke rests on foam pads over both shoulders and transfers vertical load from the rear panel. Adjustable webbing beneath the arms draws the lower edge of the rear panel toward the torso.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A back panel joins two front panels at the shoulders, and each front panel carries an inclined, top-opening pocket for a capped water sample bottle. The pockets have washable liners and adjustable webbing loops that close around the bottle necks. The wearer releases a loop to withdraw a bottle and tightens it after returning the filled bottle to the pocket.
Two shoulder-forming front panels join a back panel and carry inclined, top-opening pockets for rigid seed containers. Each container has a hinged lid with a thumb latch, and a buckle strap crosses the container shoulder below the lid to secure it in the pocket. The wearer opens either lid with one hand to dispense seed into a planting tray.
A three-dimensional warp-knit spacer mesh replaces the woven fabric back panel. Polyester webbing binds the mesh perimeter, and the upper ends of the two pocket-bearing front panels are sewn to reinforced sections of the webbing to form the shoulder straps. The mesh rests against the back, and its pile yarns maintain an air gap between the two knitted faces.
A back panel joins two shoulder-forming front panels, each of which supports a top-opening pocket with a closed bottom and closed side seams. Each pocket measures 105 mm along its centerline and has a centerline inclined 20 degrees outward from vertical at the top. A 25 mm elastic band encircles the mouth and stretches to admit a flexible flask measuring 140 mm long and 60 mm wide when filled, leaving about 35 mm exposed for gripping.
A back panel joins left and right shoulder-forming front panels, and each front panel supports a flexible flask in an inclined pocket. A sealed connector in each flask cap feeds one inlet of a manual two-inlet selector valve mounted on the chest strap. The wearer selects a flask and draws liquid through a shared tube clipped to a shoulder strap and fitted with a bite valve.
A back panel joins two shoulder-forming front panels, and each front pocket holds a container in a rigid cradle with clearance around the pocket walls. A miniature load cell between each cradle and a stiff backing plate transfers the cradle load to its front panel and measures the force along the pocket axis. A microcontroller subtracts the empty cradle readings, applies a calibration recorded with known masses in the upright position, and averages the readings over two seconds. While an accelerometer indicates an upright, stationary posture, an indicator on the heavier side lights when the estimated difference exceeds 150 g.
A woven polyester shell encloses a 6 mm closed-cell foam sheet. A spacer-knit lining faces the wearer, and perimeter stitching captures the lining and shell around the foam.
Each front panel narrows at its upper end into a 55 mm wide padded shoulder strap. The strap ends overlap reinforced corners of the back panel and attach with box-and-cross stitching.
The upper end of each front panel forms a padded strap that passes over one shoulder. Webbing sewn to each strap feeds through a ladder-lock buckle anchored to the back panel, allowing the wearer to adjust each side independently.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
To put on the shoulder harness 110, a user may place the shoulder harness 110 onto their upper torso (as one does when placing a backpack on themselves), with the back panel 111 against their back, the shoulder straps 112 going over their shoulders, the portion of the shoulder straps 112 containing the female connectors 115 in front of their shoulders, and the two ends of the chest strap 113 hanging from the bottom of the back panel 111.B · US 2021/0038421 A1 · ¶ 31
Many of these of these prior art carrying devices are dual shoulder harness assemblies made of pliable, flexible materials. When upon the shoulders, these dual shoulder harness assemblies are still widely believed to be the most comfortable systems for carrying loads such as backpacks, golf bags, and duffels; the reason being that the pliable harnesses conform easily and comfortably to the unique landscape of the user's anatomy.A · US 2006/0226183 A1 · ¶ 9
A stabilizing scapular rehabilitation brace, comprising: a shoulder harness having a chest strap, two discrete shoulder straps, at least one strap connector disposed each of the shoulder straps, and a back panel connected to the chest strap and the shoulder straps, wherein the shoulder harness is configured to be worn by a user with the each of the shoulder straps going a separate shoulder and with the chest strap encircling the user's torso; a thigh strap configured to be faB · US 2021/0038421 A1 · claim 11
An empty cell means only that no passage was reproduced there.
One of the drawbacks which has long existed for the users of these dual shoulder harness assemblies is that they are difficult to don.A · US 2006/0226183 A1 · ¶ 10
(and any other totable item), and which allows the user to heft and transport the totable load over one or more shoulders, and more specifically to an apparatus for creating an alternate point of attachment for an attachable end of a load-bearing shoulder strap.A · US 2006/0226183 A1 · ¶ 4
This invention relates to a stabilizing brace for use following injury to or surgery in the shoulder area that prevents a user from engaging in compensatory motion while moving their arm on during their physical therapy rehabilitation sessions.B · US 2021/0038421 A1 · ¶ 1
Instability is a common problem and is the root of many shoulder injuries for not only young athletes but individuals of all ages.B · US 2021/0038421 A1 · ¶ 2
patent.fyi, US 2026/0354560 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354560/, SHA-256 574965563fd05be2e8c32748d0bcf11b11a3b062b37f8ad8148b858c3383203a