1.1Use two external grooves
Two split wooden collars snap into shallow grooves around the solid handle. The groove shoulders hold the collars axially, and the collars bear against opposite faces of the disk stack.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two split wooden collars snap into shallow grooves around the solid handle. The groove shoulders hold the collars axially, and the collars bear against opposite faces of the disk stack.
The handle steps from a wide grip section to a narrow cylindrical stem that fits through the centers of the disks. The annular face at the step bears against the disk nearest the grip.
External threads on the solid handle tip engage internal threads in a molded cellulose composite cap. The cap has a flat rim wider than the disk center openings and tightens against the outermost disk.
Sisal fiber bundles sit side by side around the handle tip with their roots trapped under a crimped fiber sleeve. The free ends extend past the tip and spread radially under scrubbing pressure.
The disks slide over a grooved molded-cellulose socket, and cured water-resistant adhesive bonds their inner rims to its exterior. The socket screws onto the handle tip and transfers scrubbing loads from the disk stack into the handle.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A wooden handle carries two crosswise bamboo pins near its working end. Cotton fabric disks with central openings slide onto the handle and sit between the pins, which project from both sides. The disk edges flex into the corners of a seedling tray cell as the operator twists the handle under rinse water to loosen potting mix.
Wet-pressed cellulose pulp washers replace the fabric disks on a wooden handle. Each washer has a molded central opening that slides over the handle and radial slots that form flexible tabs around its perimeter. Two bamboo pins pass through spaced transverse holes in the handle and retain the washer stack. The tabs flex independently as the brush moves across a wet surface.
Two stainless steel hairpin clips replace the straight pins on a wooden handle that carries disks with central openings. The straight leg of each clip passes through one of two transverse holes and projects from both sides, while its curved leg grips the outside of the handle. The straight legs bound the disk stack along the handle axis, and the spring force holds each clip in its hole. Pulling the grip-side clip releases the stack for replacement.
A 10 mm diameter wooden shaft has two 3 mm transverse holes with centers spaced 18 mm apart. Two 20 mm long bamboo pins pass through the holes and project 5 mm from each side of the shaft. Eight cotton disks, each 2 mm thick with a 10.5 mm central opening, compress into the 15 mm gap between the pin surfaces. Ordered from the handle toward the tip, the disks have diameters of 36, 36, 34, 34, 30, 30, 26, and 26 mm, so the narrower tip enters a recess before the shoulders contact its sides.
A hollow cleaning pole feeds rinse water through an outlet in a clamp-on adapter. The adapter grips the wooden brush handle above two transverse pins that retain a cotton disk stack. The outlet sits beside the handle and directs water onto the disk edges. As the operator moves the pole, the disks scrub the surface and the water carries away loosened residue.
A fixture holds a predrilled handle, and a servo press inserts the tip-side pin until an optical sensor measures equal projection on both sides. A pick-and-place head slides cotton disks onto the handle from its grip end while a laser displacement sensor measures stack thickness under a fixed seating load. The controller adds disks until the measured thickness reaches the target band, then a second press inserts the grip-side pin to retain the stack.
A 12 mm solid birch dowel forms the handle. Two 3 mm through-holes run perpendicular to the dowel axis, with their centers 20 mm apart near the brush-head end.
A 24 mm bamboo dowel with chamfered ends presses through the first 3 mm hole in a 12 mm handle. The centered dowel projects about 6 mm on each side and supports the disk stack on the grip side.
A 26 mm hardwood pin tapers from 3.2 mm at the insertion end to 2.8 mm at the leading end. The taper wedges in the second 3 mm through-hole while both ends project beyond the handle and support the tip-side disk.
Eight 65 mm disks cut from needle-punched cotton felt slide onto the handle through 12 mm center openings. Radial slits extend 15 mm inward from each disk rim to form flexible scrubbing segments, and the two pins compress the stack at its center.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A nose brush comprising: an elongated handle having a first end and a second end; and a brush head affixed to at least one of the ends of the handle wherein the brush head comprises a body and fibers extending from the body, wherein the body is tapered such that the width of the brush head at a distal end is smaller than the width of the brush head at a proximal end; and the fibers are elongated and are distributed around the brush head and on the top of the brush head.A · US 2017/0238685 A1 · claim 1
A nose brush comprising: an elongated handle having a first end and a second end; and a brush head affixed to at least one of the ends of the handle wherein the brush head comprises a body and fibers extending from the body, wherein the body is tapered such that the width of the brush head at a distal end is smaller than the width of the brush head at a proximal end; and the fibers are elongated and are distributed around the brush head and on the top of the brush head.A · US 2017/0238685 A1 · claim 1
A biodegradable replacement head for an electric toothbrush, comprising: a body member having a first end and a second end and defining an internal passageway, the body member having an opening at the first end for accessing the internal passageway, the body member adapted for removable connection to an electric power/drive unit of an electric toothbrush through receipt of a portion of the electric power/drive unit within the internal passageway, the body member constructed fB · US 2022/0175126 A1 · claim 11
An empty cell means only that no passage was reproduced there.
None of the above references disclose a nose cleaning apparatus having a brush design.A · US 2017/0238685 A1 · ¶ 5
However, the nostril brush disclosed in the '336 patent also has a relatively complex design and is not disposable and biodegradable.A · US 2017/0238685 A1 · ¶ 7
As the toothbrush head is composed of or constructed from plastic, this creates a problem for the environment because the discarded toothbrushes/toothbrush heads accumulate and may not degrade.B · US 2022/0175126 A1 · ¶ 3
In some embodiments, the instant disclosure can be, alternatively or additionally, for a removable/replacement head for a non-electric handheld manual toothbrush.B · US 2022/0175126 A1 · ¶ 4
patent.fyi, US 2026/0354564 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354564/, SHA-256 4e5c36d7bbc0ac453786dd2ee8f607a93343e9cf87717659aa07e4f417db13fc