1.1Uniform pile with varying density
Both sets of rows use microfibre yarn trimmed to a 6 mm average pile length. The dense rows place more fibre tips against the floor, while the sparse rows leave more space between tufts for loose particles.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Both sets of rows use microfibre yarn trimmed to a 6 mm average pile length. The dense rows place more fibre tips against the floor, while the sparse rows leave more space between tufts for loose particles.
A 4 mm microfibre strip sits on a backing land 4 mm higher than the land carrying an 8 mm strip. The two strips reach the same nominal outer radius, and the longer fibres have more free length to bend during floor contact.
Two strips have average pile lengths of 7.8 mm and 8.0 mm and sit on the same cylindrical backing. Finer filaments in the longer strip bend more readily, while thicker filaments in the shorter strip provide firmer contact as the pile compresses against the floor.
Two pile heights are tufted into neighboring regions of a single backing, with normal tuft spacing maintained across the boundary. The backing wraps around the core, and the alternating pile heights change the depth of floor contact as the roller turns.
Two 20 mm wide helical strips flank a 6 mm wide exposed channel, with both dimensions measured across the strips. The channel gives loose particles room to move between the pile bands as the bands sweep them toward the suction inlet.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A driven microfibre roller mounts across the return run of a dry packaging conveyor, opposite a backing idler. Four straight strips run along the roller and alternate between 8 mm and 10 mm average pile lengths. Each strip is 20 mm wide measured around the core, and a 2 mm gap separates neighboring strips. The roller surface moves against the belt travel at the contact line and sweeps loose particles into a removable tray.
Split nylon microfibre pile replaces the pile material in each portion, with two carriers bearing 9 mm average pile and two bearing 12 mm average pile. Each pile strip bonds to a straight carrier that slides axially into a retaining slot in the roller core. The slots alternate the two pile heights around the core and leave 3 mm of bare core between neighboring 25 mm wide strips. An end plate retains the carriers during rotation and releases them for replacement.
A 120 mm long roller with a 20 mm core diameter carries five straight axial microfibre strips with average pile lengths of 3.0, 3.2, 3.5, 3.8 and 4.2 mm. Each strip occupies one fifth of the core circumference together with its following gap, and each gap is one tenth as wide as a strip. The strips follow increasing pile height around the core. A height stop sets the unloaded core surface 2.7 mm above a flat floor so that each strip contacts the floor in turn.
A 400 mm long roller with an 80 mm core diameter carries four adjacent 100 mm wide axial rows of microfibre patches. Each row has eight equally spaced patches that alternate between 7 mm and 9 mm average pile lengths, with a 3 mm circumferential gap between patches about 28.4 mm wide. Each successive row starts 11.25 degrees farther around the core than the preceding row. The offsets spread the passage of patch edges through the floor contact line across successive angular positions.
A wet floor extractor carries a motor-driven roller between a liquid spray manifold and a trailing suction squeegee. The roller has four straight axial strips that alternate between 8 mm and 12 mm average pile, with a 3 mm gap between neighboring 20 mm wide strips. The manifold wets the floor ahead of the roller, and the rotating strips scrub the wetted surface. The squeegee draws the spent liquid and suspended debris into a recovery tank.
A motor drives a roller with alternating 8 mm and 11 mm average pile strips, each 24 mm wide and separated from its neighbors by a 3 mm gap. A rotary encoder supplies speed and revolution timing, and a current sensor measures the motor current. After the roller reaches its speed setpoint, a controller averages the current over four revolutions and compares the result with a preset band. A screw actuator raises the brush carriage by 0.25 mm above the upper threshold and lowers it by 0.25 mm below the lower threshold, then the controller repeats the measurement within the carriage travel limits.
Alternating microfibre bands have average pile lengths of 5 mm and 7 mm on a common cylindrical core. The longer pile contacts the floor first, and the shorter pile engages as the roller compresses the longer fibres under load.
Three microfibre portions have average pile lengths of 4.0 mm, 5.0 mm and 6.25 mm. Dividing the shorter length by the longer length in each neighboring pair gives 80% for both pairs.
Two 25 mm wide microfibre strips leave a 3 mm exposed channel between their facing edges. Measured perpendicular to the strip edges, the channel is 12% of either strip's width.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As means for achieving such a structure in pile goods, a method comprising causing a non-shrinkable fiber and a shrinkable fiber having different shrinkage percentages to be present in a pile part; causing the shrinkable fiber to shrink in the pile prefinishing step; and causing a step to appear in the pile part based on the difference in shrinkage percentage at that time is generally used.A · US 2007/0074353 A1 · ¶ 2
Bristles 83, which are arranged in circumferentially spaced strips, extend radially outwardly from the cylindrical body 70.B · US 9,867,515 B2 · ¶ 34
An empty cell means only that no passage was reproduced there.
Accordingly, there has not been reported so far a pile fiber using an acrylic shrinkable fiber that can be dyed in a low-temperature region and can shrink to a certain extent by dry heat treatment using a pin tenter or the like.A · US 2007/0074353 A1 · ¶ 7
The present invention can increase number of colors assort in the down hair part of a step pile fabric more easily than before by carrying out dry heat treatment of a pile fabric comprising an acrylic shrinkable fiber that can be dyed in a specific low-temperature region.A · US 2007/0074353 A1 · ¶ 8
This invention relates to a cleaner head for a cleaning appliance and particularly, although not exclusively, relates to a cleaner head for a vacuum cleaner, such as a vacuum cleaner for domestic use.B · US 9,867,515 B2 · ¶ 2
Types of debris picked up during cleaning include dust, dirt, food particles and hair Fluff and bundles of hair can be problematic because they can become stuck on the bristles of the brushbar or trapped within the cleaner head.B · US 9,867,515 B2 · ¶ 4
patent.fyi, US 2026/0354566 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354566/, SHA-256 472e42006d3e474048bd4327b6cb037baa5983b152088ddf26035dd04e88d675