1.1Magnetic drive across a wall
The motor shaft turns an internal disk carrying alternating magnetic poles. Across the nonmagnetic end wall, a matching disk fixed to the roller follows the rotating magnetic field and drives the roller.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The motor shaft turns an internal disk carrying alternating magnetic poles. Across the nonmagnetic end wall, a matching disk fixed to the roller follows the rotating magnetic field and drives the roller.
A motor pulley and a toothed ring on the drum mouth engage a synchronous belt inside the guard. The ring turns with the drum, and bearings on the stationary tube carry the radial belt load.
Guard-mounted end brackets hold annular bearings around smooth journals on the drum exterior. The bearings locate the roller radially and axially, leaving clearance around the motor tube as the output coupling turns the drum.
Two bolts clamp a grip bracket to a flange that projects axially beyond the guard. The bracket transfers pushing and twisting loads to the seat, and the guard clears the bracket.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handheld brush scrubs soil from empty seedling trays at a greenhouse wash bench. The motor sits inside the stationary tube, and its output shaft drives a drum fitted around the tube with flexible nylon bristles long enough to reach into the tray cells. The outer cover carries the grip and surrounds the upper half of the drum, leaving the lower half exposed to the tray. The operator guides the roller along each row of cells while a bench spray nozzle rinses the loosened soil into a drain pan.
A pair of opposing permanent magnet rings replaces the mechanically engaging shaft fitting and drum socket. A hub on the output shaft carries the driving ring, and the inside face of the drum bottom carries the driven ring across an axial air gap. Alternating north and south poles around each ring transmit torque across the gap as the shaft turns. Bushings between the drum and the stationary tube center the roller, and a thrust washer and retaining ring hold the axial gap.
A molded thermoplastic polyurethane sleeve with flexible fins replaces the bristle tufts on the roller drum. Internal ribs on the sleeve engage longitudinal grooves in the drum to transmit torque, and end collars hold the sleeve in place axially. Rows of fins form opposite helices on the two halves of the sleeve and meet at the roller midpoint. As the drum rotates around the stationary motor tube, the exposed fins flex against the surface and sweep loose particles toward the midpoint.
A roller for recessed channels has a 24 mm drum diameter, a 35 mm working width and 4 mm radial bristles, giving a 32 mm bristle tip diameter. A 12 mm diameter geared motor fits inside a stationary tube with a 13 mm bore and a 16 mm outside diameter. Two sleeve bushings with 16 mm bores support the drum on the tube, and the motor output shaft engages a keyed socket at the drum bottom. The roller runs at 300 rpm, and the guard maintains a nominal 2 mm radial clearance from the bristle tips over the upper half of the roller.
The outer cover incorporates a suction slot that spans the roller width just behind the point where the bristles contact the surface in the normal direction of travel. A molded passage connects the slot to a hose barb on the cover, and a flexible hose leads to a wet vacuum collection tank. Flexible skirts on either side of the slot limit air leakage while admitting loosened debris and liquid. The motor inside the stationary tube rotates the drum while the vacuum draws the debris and liquid through the slot into the tank.
A controller in the grip measures motor current through a shunt and shaft speed through a Hall sensor that reads a magnet on the output hub. The controller ignores the startup current for 200 ms, then detects a jam when current exceeds twice the calibrated free-running current and speed remains below 20 percent of the commanded speed for 150 ms. A bidirectional motor driver stops the roller, waits 300 ms and reverses the roller at one-third of the commanded speed for 250 ms. The controller then resumes forward rotation and requires the operator to release and press the trigger again if the jam recurs within two seconds.
A steel output shaft passes through a clearance hole in the tube end wall. A parallel key transfers torque from the shaft to a splined hub, and a retaining ring holds the hub axially.
Two sealed ball bearings sit in molded pockets inside the roller, with their inner rings located on journals on the motor accommodating tube. Nylon bristle tufts are anchored in staggered rows around the roller surface.
A molded grip foot seats against a flat pad on the outer wall of the protective cover. Two screws engage brass inserts in the pad, and a molded locating rib transfers side loads into the cover.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A combination of a variable frequency drive motor 38 and a gear box 40 are positioned on the upper frame 28 of the trommel support structure 26. A drive shaft 42, shown in FIGS. 1 and 3, operatively connects the variable frequency drive motor and gearbox combination to the drive wheels 34 which are frictionally engaged with the collars 24 to rotate and operate the drum 14 at the desired drum rotation speed.A · US 2009/0038996 A1 · ¶ 23
A drive shaft 42, shown in FIGS. 1 and 3, operatively connects the variable frequency drive motor and gearbox combination to the drive wheels 34 which are frictionally engaged with the collars 24 to rotate and operate the drum 14 at the desired drum rotation speed.A · US 2009/0038996 A1 · ¶ 23
The fixed handgrip part integrally connected to the shifter housing has a corresponding length in the axial direction.B · US 8,850,919 B2 · ¶ 3
An empty cell means only that no passage was reproduced there.
The disposal of the increasing volume of municipal solid waste, as part of the more general problem of environment, has caused rising concern in recent years.A · US 2009/0038996 A1 · ¶ 2
On a narrower but no less gainful scale, the present invention provides a rotating screening drum which enhances the recovery of coins from a non-ferrous residue throughput as it flows therethrough.A · US 2009/0038996 A1 · ¶ 4
This places corresponding demands on the size of injection moulding machines used for the production of the shifter, which is a disadvantage.B · US 8,850,919 B2 · ¶ 3
This design includes the possibility of providing and using a twist-grip shifter both in a variant with and a variant without a separate fixed handgrip part.B · US 8,850,919 B2 · ¶ 4
patent.fyi, US 2026/0354567 A1, claim 1, first published 2026-11-19T00:16:15-05:00, https://patent.fyi/US20260354567/, SHA-256 a0853893f2932c69f1861aa6da74d1b5d658c2c5a9ad58ff767b7255cee004fc