1.2Rotating discs for detangling
Rounded polymer discs turn on transverse axles recessed into the front of the head. Staggered rows guide strands into gaps between discs, and the disc rims roll as hair passes over them.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Rounded polymer discs turn on transverse axles recessed into the front of the head. Staggered rows guide strands into gaps between discs, and the disc rims roll as hair passes over them.
The rear forms a cylindrical arc with a 20 mm radius and a smooth elastomer skin. A detangled hair section wraps over the arc under light tension, and the skin supplies friction as the section slides off.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Injection-molded thermoplastic elastomer fins replace the front bristles. Each fin has a tapered cross-section and a rounded free edge, and staggered rows of fins project from a common backing plate that snaps into the front of the head. The fins bend as fiber bundles pass between them, and the rear grooves and perimeter notches guide the separated bundles during curl shaping.
Each rear groove has a flat floor 3 mm wide and two concave flanks that rise 2 mm from the floor to the neighboring ridges. Each channel extends across the rear and opens at both ends into perimeter notches with matching profiles. A hair section enters through one notch, spreads across the floor under light tension, and exits through the opposite notch.
An oval head measures 65 mm long and 28 mm wide and carries three transverse rear grooves with 60-degree included wall angles. Adjacent ridge centerlines sit 8 mm apart, and each groove opens into a perimeter notch at each end. Front bristles detangle a small section, and the operator feeds the section through one groove while rotating the head.
A geared motor in the handle rotates an oval head around its long axis, and front bristles detangle the section before the section enters a rear groove through a perimeter notch. A strain gauge on the stationary motor mount measures reaction torque, and a controller samples it at 100 Hz while the motor turns at 15 revolutions per minute. The controller stops the motor when torque exceeds a preset limit and waits for the operator to release and press the rotation button again.
A 4 mm radius defines the molded channel from lip to lip. The curved surface centers the hair section under tension and supports it as it slides across the rear.
Rounded nylon pins project 15 mm from a thermoplastic elastomer pad seated in the front of the head. The pad flexes locally under load as the pins separate strands.
Molded notches open through the perimeter where the rear grooves meet the edge. Each notch has a 4 mm opening and 0.75 mm radii at its entry edges to guide hair over the rim.
Two molded planar walls define a 40 degree included angle in a cross section perpendicular to each groove. A 0.5 mm root radius joins the walls and provides a rounded contact surface.
Adjacent protrusions have a 14 mm center-to-center spacing measured across the grooves at the midpoint of the rear surface. The repeated spacing sets a consistent interval between hair paths.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The ferrule has oppositely facing front and back walls 26, 28 and a pair of oppositely facing side walls 30, 32 which interconnect the front and back walls. The side walls have a width which is short relative to that of the front and back walls.B · US 8,905,363 B2 · ¶ 23
The block structure 34 mounts a plurality of bristle tufts 36a, 36b, 36c, 36d (seen best in FIG. 2). In the preferred construction the bristle tufts are inserted into complementally shaped bores in the block structure 34 and are secured thereto by adhesive, staples, etc.A · US 2013/0104327 A1 · ¶ 21
An empty cell means only that no passage was reproduced there.
It has been found that there is a need for an inexpensive, but effective cleaning implement for cleaning floors that have grout lines, such as those found in kitchens and bathrooms.A · US 2013/0104327 A1 · ¶ 3
By making the bristle tufts of one row to have a greater length than the second row, engagement of the distal ends of the first row of bristle tufts with a thin grout line is greatly facilitated.A · US 2013/0104327 A1 · ¶ 7
The problem with using a paint can for this purpose however is that paint can run from the can onto a surface on which it rests.B · US 8,905,363 B2 · ¶ 3
Furthermore the attachment means is not as susceptible to breakage as are projecting attachment means such as those mentioned above.B · US 8,905,363 B2 · ¶ 5
patent.fyi, US 2026/0354570 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354570/, SHA-256 d93c8802607d14d2dda1879a7e2e8c8fe5ce6f78fb63a04bc5546fe998e583bb