1.1Permanently riveted support ledges
Solid steel rivets pass through the upright and the vertical flange of each ledge. A press upsets the rivet tails, and the horizontal flanges carry the module load at a fixed height.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Solid steel rivets pass through the upright and the vertical flange of each ledge. A press upsets the rivet tails, and the horizontal flanges carry the module load at a fixed height.
Two horizontal steel tubes span between the upright mounts, one near the front and one near the rear. Bolts through the module base secure it to threaded inserts in the tubes, which carry its weight to both uprights.
Each mount has two clevises that receive upper tabs on the module mounting panel. Captive pins pass through the clevises and tabs, transferring vertical load in double shear while the lower edge stays clear of the mount.
The mount studs enter blind sockets in the upright, and each stud has a transverse bore. Captive pins inserted from the front edge of the upright pass through the bores and block stud withdrawal.
After the module seats on its ledges, a captive round pin on each mounting panel drops into a vertical bore in the corresponding mount. The pin and bore carry lateral load in shear, keeping the mount seated against the upright while the module is in place.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse potting bench has two perforated stainless steel uprights with their hole rows facing inward. A removable mount on each upright supports the lower edge of a side plate on a drained polypropylene bin for pots and hand tools. Inward flanges on the bin side plates overlap the inner edges of the mounts, and the operator lifts the bin until the flanges clear the mounts before removing it.
Two flat, downward-hooked sheet-steel tabs replace the round mounting projections on each mount, and rectangular slots replace the round holes in each upright. The installer inserts the tabs through the slots and lowers the mount until the tab shoulders rest on the lower slot edges. The module side plates rest on the mounts, and a downward flange on each side plate overlaps the inner edge of its mount to limit inward movement.
Two stainless steel spring fingers near the front and rear of each module side plate replace a continuous retaining flange. Each finger has a ramped lower tip that deflects inward as the module is lowered and returns outward after the tip passes the top of the mount. The side plate lower edge carries the vertical load, and square shoulders on the fingers bear against the inner edge of the mount if it shifts inward. The fingers clear the mounts when the module is lifted vertically.
The upright inner faces are 300 mm apart, and the module measures 298 mm across its side plates. Each upright has a vertical row of 6 mm holes on 12.5 mm centers, and each mount engages two holes 25 mm apart. With the module fully seated, each retaining flange extends 5 mm below the top of the mount alongside its inner edge. Moving both mounts by one hole position changes the module height by 12.5 mm.
A rectangular carrier spans the two uprights and has side plates that rest on the removable mounts. Downward flanges on the carrier side plates overlap the inner edges of the mounts. Full-extension ball-bearing slides attach to the inward faces of the carrier side plates and carry a drawer. Two hand-operated latches on the carrier capture the underside of the mounts during drawer travel and release the carrier for lift-out removal after the drawer is detached.
Each mount carries a small permanent magnet near its inner edge, and each module retaining flange carries a Hall-effect sensor opposite that magnet when seated. A controller in the module compares each sensor reading with a threshold set using the fully seated position. The controller illuminates a green indicator when both sensors exceed their thresholds and identifies the unseated side when only one does.
A die-cast metal mount carries two steel studs that project horizontally into matching holes in the upright. The paired studs resist rotation under load and withdraw together when the unloaded mount is pulled toward the cabinet center.
Each steel mounting panel has a lower edge folded into a horizontal flange. The underside of the flange seats on the flat top of the mount and spreads the vertical load over the contact area.
A downturned steel lip runs front to rear along part of each mounting panel. When the module seats, the lip extends below the top of the mount on its inward side, trapping the mount between the lip and the upright.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Often, the cabinet walls are provided with vertically spaced rows of bores in which fixed length pins or other fasteners are removably inserted, on which pins a shelf is then positioned.A · US 2007/0284983 A1 · ¶ 2
A shelving system, comprising: (a) right and left mirror image side panels, each having a first inside surface with shelving peg holes, (b) a plurality of shelf support pegs configured and arranged for selective and releasable engagement within the shelving peg holes, (c) at least one shelf configured and arranged for gravitational support between the side panels upon the shelf support pegs extending from the side panels so as to present an upward load contacting surface andB · US 8,813,980 B1 · claim 1
Referring to FIGS. 3 and 10-12, the bracket 19 includes a main wall 40 that projects vertically and has a mounting slot 41 on the bottom thereof which has a width dimensioned to closely fit over the diameter of the pin body 35 so as to be vertically supported thereby.A · US 2007/0284983 A1 · ¶ 28
A shelving system, comprising: (a) right and left mirror image side panels, each having a first inside surface with shelving peg holes, (b) a plurality of shelf support pegs configured and arranged for selective and releasable engagement within the shelving peg holes, (c) at least one shelf configured and arranged for gravitational support between the side panels upon the shelf support pegs extending from the side panels so as to present an upward load contacting surface andB · US 8,813,980 B1 · claim 1
An empty cell means only that no passage was reproduced there.
While a plurality of vertically spaced positions are defined for mounting the shelf thereon, the rows of unused bores are constantly visible and can be unsightly.A · US 2007/0284983 A1 · ¶ 2
As such, no unsightly holes are left in the wall face, and the shelf pin assembly can serve as an aesthetic surface detail of the cabinet wall.A · US 2007/0284983 A1 · ¶ 5
However, such designs are limited in construction size and weight bearing load and are difficult to change the layout once constructed.B · US 8,813,980 B1 · ¶ 5
Therefore, a need exists for a versatile shelf with greater weight supporting capacity and versatility at greater shelf lengths.B · US 8,813,980 B1 · ¶ 5
patent.fyi, US 2026/0354576 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354576/, SHA-256 60cc252572333ab1a7438532b4dc6472e74ce08d3890dc889ad5c4b33e600cf0