1.1Folded sheet side panels
Each steel side panel has a return flange along its front and rear edges to stiffen the sheet. Rail brackets bolt through the panels, and a rear cross brace holds the panels square.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each steel side panel has a return flange along its front and rear edges to stiffen the sheet. Rail brackets bolt through the panels, and a rear cross brace holds the panels square.
Rollers span the shelf from side to side and let the bin roll in and out. A spring-loaded front stop rises behind the lower front edge of the seated bin and drops when the user presses a release lever.
The bin lips bear on continuous, flat rail tops. As the bin reaches its seated position, spring-loaded pins mounted beside the rails enter holes in the bin sidewalls and block travel in both directions. A front lever retracts both pins for removal.
A short bearing segment of the lip has a flat underside flush with the surrounding lip and fits between the two transitions. During insertion, the lip crosses the front transition and drops into the relief under the bin's weight. The transitions resist fore-and-aft motion until the user lifts the bin enough to clear them.
The rail surface stays at the floor height of the relief from the seating area to the rear end. A rubber bumper fixed to a rear crossmember contacts the back wall of the bin and sets the inward travel limit. The front transition resists outward travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse rack carries shallow propagation trays on opposing stainless steel rails that support the lips at the trays’ short ends. Each short-end lip has a downward lug that drops into a rail recess with sloped front and rear shoulders. An operator lifts the tray until both lugs clear the shoulders, then slides it forward for transplanting. A sloped gutter below each tier collects drainage and directs it to a return pipe.
A screw-fastened acetal insert replaces the recessed section of each aluminum support rail, with the insert edges flush with the adjacent running surface. Each insert has a flat seat for the bin lip and a pocket bounded by front and rear shoulders for the downward lug. The lip slides across the rail and insert until the lug drops into the pocket. Lifting the bin clears both shoulders for withdrawal.
Rows of sealed bearing rollers replace the continuous sliding surfaces on the opposing rails, with the roller axes transverse to the direction of bin travel. Each roller row has a gap at the storage position, where a fixed saddle supports the short-end lip and receives its downward lug. The rollers carry the bin during insertion until the lugs settle between the front and rear shoulders of the saddles. Lifting the bin clears the shoulders and returns the lips to the roller rows for withdrawal.
A 700 mm wide and 300 mm deep frame carries four opposing rail pairs at a vertical pitch of 140 mm. Each bin measures 600 mm across its outer lip edges and 250 mm front to back, with a 100 mm body height and 15 mm of lip overlap on each rail. Each short-end lip carries a 12 mm long lug projecting 5 mm downward into an aligned recess with a 14 mm flat seat and a depth of 6 mm. A 7 mm vertical lift clears the front shoulders before the bin slides forward.
A forced-air drying cabinet contains a removable stainless steel frame with opposing rail pairs supporting perforated trays by their short-end lips. The tray lugs seat in rail recesses whose front and rear shoulders retain the trays while air circulates. A rear plenum distributes heated air through slots between tiers, and a return grille below the rack feeds the recirculation fan. A cabinet door switch interrupts heater power during tray access.
A motorized carriage aligns with a tier and grips a flange at the front of the bin. The carriage advances the bin along the opposing rails until the lugs reach the recesses, then lowers its gripper so the lugs settle against the recess seats. A switch beside each recess detects the corresponding lip at its seated height, and the controller releases the gripper only when both switches are active. For retrieval, the carriage grips the flange, raises the bin above the shoulders, and withdraws it.
Four square steel tube posts define a frame 760 mm wide and 420 mm deep. Bolted crossmembers set the post spacing, and a rear diagonal strap resists side-to-side racking.
Each rail pair uses two steel angles with horizontal flanges facing inward at the same height. Bolts through the vertical flanges attach the rails to the posts, and the horizontal flanges carry the opposing bin lips.
The top of each rail has a 3 mm deep pocket with a sloped front edge and a steeper rear edge. A molded rib projects downward from each bin lip and drops into the pocket as the bin reaches its seated position. Pulling the bin outward drives the ribs up the front ramps and lifts the bin, while the steeper rear edges limit inward travel.
A rectangular bin measures 620 mm across the rack and 350 mm from front to back. Molded lips along its two 350 mm sides rest on opposing rails that run from front to back.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Support frame 110 generally includes four upright corner columns or posts 112 and a pair of side cross members 116 and end cross members 118 each connecting the top ends of two corner posts.A · US 2015/0323122 A1 · ¶ 18
Front sidewall 122 may be configured to limit the forward movement of the bin in a direction towards proximal end 102. In embodiments, responsive to positioning a bin on bin receiver 120, the bin may be positioned adjacent to front sidewall 122.B · US 2020/0189439 A1 · ¶ 29
An empty cell means only that no passage was reproduced there.
While these automated lifts are popular and have convenient features, the mechanisms used to raise and lower the platforms have heretofore suffered from a variety of operational and manufacturing problems.A · US 2015/0323122 A1 · ¶ 2
The flexibility of the timing belt and the serpentine engagement of the timing belt around the idle rollers and the pinion ensures positive actuation of the platform between its raised and lowered positions and eliminates the chance of slippage.A · US 2015/0323122 A1 · ¶ 4
Accordingly, needs exist for improved mobile bin tippers that are configured to receive, lift, and rotate bins allowing for removal of the content of bins.B · US 2020/0189439 A1 · ¶ 5
This may reduce the number of bins required to service numerous locations, while also reducing the amount of time required to empty documents within the bins to later shred the documents.B · US 2020/0189439 A1 · ¶ 6
patent.fyi, US 2026/0354578 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354578/, SHA-256 0deb2cb6087e37add458ca7a7ca0647b7673fdbd38ae65af61edcac829159569