1.1Corrugated leaf spring strips
Parallel spring steel strips have repeating arched sections with feet seated in base channels. A flexible top sheet transfers load to the arch crowns, and the arches flatten elastically under compression.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Parallel spring steel strips have repeating arched sections with feet seated in base channels. A flexible top sheet transfers load to the arch crowns, and the arches flatten elastically under compression.
Each wire spring wraps once around a horizontal pin. One arm seats against the base and the other bears against a load pad, so downward pad travel rotates the arms relative to each other and bends the wire elastically.
Each coil has circular turns wound about a vertical axis and sits in a fabric pocket. Successive rows shift by half the center spacing within a row, placing each interior coil next to six neighbors.
The wire follows four straight runs connected by circular arcs tangent to both adjoining runs. The straight runs of neighboring coils face each other across a narrow clearance, while the projected gaps widen around the arcs.
Square-profile coils share the same orientation, and their center grid sits at 45 degrees to the coil sides. A flexible polymer sheet spans the resulting gaps and distributes local loads to the top turns of several coils.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A transit seat cushion uses a shallow array of polygonal wire coils between a stamped seat pan and an upholstered load-spreading pad. Lower end turns seat in recesses in the pan, and neighboring side portions run alongside each other across the sitting area. The pad spreads occupant loads across several upper end turns, and the recesses hold the coils in position during repeated loading.
Cold-rolled spring steel strip replaces round wire as the stock for each polygonal coil. A forming mandrel bends the strip around radiused corners while the feed advances axially to set the pitch, with the broad faces of the strip facing inward and outward. The strip thickness, width, and pitch set the axial spring rate, and the turn spacing provides clearance through the working stroke.
An innerspring unit uses coils with a free height of 150 millimeters and a common polygonal footprint. Coils in the center third of the mattress length have five active turns, and coils in the two end zones have seven active turns. The coils use the same wire diameter and end-turn geometry, with the pitch adjusted in each zone to maintain the common height. The five-turn coils provide a higher initial axial spring rate than the seven-turn coils.
A mattress on a powered articulated base uses separate groups of polygonal coils over the head, seat, and leg deck sections. Each group has its own flexible carrier sheet, and the edges of neighboring groups end on opposite sides of the corresponding deck hinge. A continuous foam layer spans the hinge lines and flexes as the actuators rotate the deck sections.
Each polygonal coil sits in a gusseted thermoplastic fabric pocket with fold lines registered to the coil corners. The pockets form continuous rows through transverse ultrasonic seams, and adhesive beads join neighboring rows along facing pocket walls. The fabric lies between adjacent metal side portions and flexes when individual coils compress under a local load.
An overhead camera records the top-view outline and angular orientation of each coil on an indexed conveyor. Image-processing software fits lines to the projected side portions and calculates the rotation and translation needed to align each coil with its location in an assembly fixture. A robot grips the upper end turn, applies the calculated pose, and places the coil into a lower-turn locating nest. A second image checks the resulting gaps against the programmed assembly tolerances.
A wire former bends high-carbon spring steel into five turns with a square top-view profile. The coils sit on a square grid with 64 mm center spacing and 62 mm across opposite outer faces, leaving a nominal 2 mm gap between facing sides.
Each coil has six straight side portions per turn, joined by bends that change the wire direction by 60 degrees in top view. The coil centers form a triangular grid, and each interior coil presents one flat side to each of its six nearest neighbors.
Rectangular coils sit in aligned rows with long side portions facing across each row boundary. Helical lacing wires wrap around facing side portions of the top and bottom turns to hold the row spacing under load.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Each coil spring (110) has a barrel (140) of uniform diameter containing several turns of the coil spring (110) and a head and base (both of which are partly hidden) of larger diameter than the barrel (140).A · US 2008/0237948 A1 · ¶ 25
The mattress 16 is constructed in a manner well-known in the art and includes a layer of a plurality of pocketed coil springs 30, as will be described in detail hereinafter, arranged in an array having a generally rectangular shape in plan. As seen in MG. 1, the coil springs 30 are closely packed together with their longitudinal axes A-A all parallel one to another and with their longitudinal ends 31, 32 all lying in a common plane thereby defining a coil innerspring unit 20.B · US 2023/0389713 A1 · ¶ 23
An empty cell means only that no passage was reproduced there.
The force is greater at the center of the mattress, which is the location of the hips portion in sleeping position.A · US 2008/0237948 A1 · ¶ 6
The invented innerspring structure introduces an additional resilient material into the center portion of the innerspring unit to create additional support for the extra load of the hips portion in our body while in sleeping position.A · US 2008/0237948 A1 · ¶ 7
The use of different coil geometries and different gauge wires creates a burden for the mattress manufacturer as it needs to be cognizant of which strings of coils are to be placed into the innerspring unit and at which location in order to create the desired mattress.B · US 2023/0389713 A1 · ¶ 4
Disclosed herein mattress assemblies including coil innerspring units, coil innerspring units by themselves, and processes for making the coil innerspring units, wherein the coils within the coil innerspring unit are manufactured with the same geometry, same composition, and from the same gauge wire using different heat treatments to provide the coil innerspring unit with different spring rates.B · US 2023/0389713 A1 · ¶ 5
patent.fyi, US 2026/0354600 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354600/, SHA-256 0dd02eda701269dba9fbdfd6d08ea9d4d71cbc7bc9583a11f6c1c260f0bb4a50