1.1Recess behind the stretcher
The stretcher fits against the walls of the frame opening and seats on inward-facing shoulders. A removable rear panel sits 8 mm behind the stretcher and forms a recess for the retaining hardware.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The stretcher fits against the walls of the frame opening and seats on inward-facing shoulders. A removable rear panel sits 8 mm behind the stretcher and forms a recess for the retaining hardware.
Four rigid brackets attach to the back of the frame and extend over the stretcher bars. Short wood screws pass through the brackets into pilot holes in the rear faces of the bars, while a continuous gap separates the side faces.
Slide assemblies screw to the rear faces of the stretcher bars. Each rigid bolt extends into a blind pocket machined directly into the frame, and a captive thumbscrew locks the bolt in its extended position.
Rigid aluminum blocks bolt into keyed seats at the rear of the frame. Each block presents two flat faces to locate a stretcher corner and a projecting lip that captures the rear edge of the stretcher.
Threaded bushings in the frame walls carry adjustment screws with rigid swivel shoes. Turning each screw advances its shoe against the stretcher side, and a locknut holds the screw position.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An aluminum wall frame surrounds a fabric-covered acoustic absorber cassette with rigid edge rails. A recessed channel in the frame creates a peripheral cavity around the cassette, and a continuous elastomer lip bonded to the channel wall projects into the cavity. As the cassette enters the frame, its edge rails deflect the lip, which presses against the rails and holds the cassette by friction.
Coil-spring plungers replace the flexible contact member and seat in radial bores in the interior side face of the frame. Each plunger carries a rounded polymer shoe that projects into the peripheral cavity and slides radially in its bore. The picture member pushes the shoes outward during insertion, and the compressed springs press the shoes against its exterior side faces to provide frictional retention.
Permanent magnets replace the flexible contact member and mount in recesses in the interior side face of the frame. Thin steel strips bonded to the exterior side faces of the stretcher form the mating surfaces, and the frame channel leaves a peripheral cavity alongside them. The magnets draw the strips against thin elastomer pads over the magnet faces, and friction at the pads resists withdrawal of the stretcher.
A frame with an inside opening of 524 by 424 mm surrounds a 500 by 400 by 60 mm rigid canvas stretcher and provides a 12 mm side clearance when centered. A hollow elastomer gasket runs around the interior side face and projects 15 mm into the clearance in its free state. The centered stretcher compresses the gasket by 3 mm on each side, and the gasket grips the stretcher along its exterior side faces.
A recessed channel in the front portion of the frame houses low-voltage light strips behind a translucent diffuser. The channel faces inward toward the display surface, and its wiring runs through a passage in the frame to a rear power connector. Behind the lighting channel, a resilient gasket bonded to the interior side face projects into the peripheral cavity and grips the canvas stretcher along its exterior side faces.
A fixture holds the frame face down while an overhead camera measures the opening and the outside edges of the canvas stretcher. A controller uses those measurements to center the stretcher over the peripheral cavity, then lowers it with an actuator fitted with a force sensor. A resilient strip fixed to the interior side face deflects during insertion and grips the stretcher when the actuator releases it at the programmed depth. The controller stops and retracts the actuator if the measured force exceeds a preset limit before that depth.
Four solid silicone strips line the frame opening, and their mitered ends meet at the corners. The strips compress against the sides of the stretcher to center it, and rear tabs hold the stretcher against a front lip.
Four mitered hardwood rails form a rectangular opening with 6 mm of clearance on each side of the stretcher. A routed ledge sets the insertion depth and leaves the side cavity open toward the front.
Screw-mounted magnets on opposing interior frame faces contact steel plates fastened to the exterior stretcher faces. Each plate seats in a shallow pocket in its magnet housing, where the pocket walls resist forward and rearward movement.
Two rivets secure each 0.5 mm stainless steel leaf spring to an interior frame face. A rounded bend at the free end rides over the stretcher edge during insertion and presses against the exterior side face once seated.
A screwed aluminum carrier fixes molded polyurethane fingers to each interior frame face. The stretcher deflects each finger outward by 1 mm during insertion, and elastic recovery presses a molded rib into a shallow groove on the exterior stretcher face.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
According to one example, the receiving recess 203 can form a laterally closed cavity with a front opening into which the leaf spring end 205 can be pushed from the front.B · US 2017/0113504 A1 · ¶ 41
Symmetry of the leaf spring retaining bracket about two planes simplifies assembly procedures and reduces the number of different suspension components required.A · US 2005/0179224 A1 · ¶ 24
An empty cell means only that no passage was reproduced there.
A leaf spring retaining bracket is needed that may be used on either side of the vehicle frame.A · US 2005/0179224 A1 · ¶ 6
A one-piece leaf spring retaining bracket may be welded to either side of a vehicle frame.A · US 2005/0179224 A1 · ¶ 7
The leaf spring, however, can be highly stressed in the retainer, which is undesired.B · US 2017/0113504 A1 · ¶ 3
In this way, stress on the leaf spring end in the retainer is reduced, which can lead to longer service life of the connection between the leaf spring end and the retainer and therefore a longer service life of the leaf spring.B · US 2017/0113504 A1 · ¶ 6
patent.fyi, US 2026/0354604 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354604/, SHA-256 c0d966d8f447868f3e7b4f6a9b6cdd3d424b1ba6ed5a3136e38d431375fe0039