1.1Rounded bottom in a cradle
A molded cradle has a curved recess that matches the lower edge of the cover. The recess supports the pillow on both sides of its lowest point, and the flat underside of the cradle rests on the support surface.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A molded cradle has a curved recess that matches the lower edge of the cover. The recess supports the pillow on both sides of its lowest point, and the flat underside of the cradle rests on the support surface.
Two padded clamp bars on a flat steel plate grip a reinforced fabric hem along the bottom of the cover. The plate extends forward and rearward of the cover to resist tipping.
Two thermoformed polypropylene shells laminated with fabric form the domed front and rear faces. A flexible fabric band joins the shells around their edges, and a small opening in the band vents the cavity.
Two webbing loops pass through reinforced openings at the top of the cover and join the upper rail of the internal frame to a crossbar on a stand behind the pillow. The loops hold the upper rail upright while the bottom of the pillow rests on the tabletop.
A fabric-reinforced air chamber pushes the upper edge of the cover away from the base and tensions four diagonal webbing stays. The crossed stays carry tensile loads between the base and upper edge and limit sideways movement.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A textile cover carries printed exhibit information on its front face and has a straight bottom that rests on a display plinth. An internal steel base sits in a fabric pocket sewn to the bottom, and a rigid panel rises from a socket in the base. Foam pads on both sides of the panel smooth the cover and keep the printed face upright.
A single injection-molded polypropylene panel serves as the rigid internal frame. Ribs molded into the rear surface stiffen the panel, and an integral tongue at its lower edge slides into a matching slot in the internal base. Foam pads surround the panel, and a pocket sewn along the straight bottom of the cover holds the base.
Shaped pads cut from three-dimensional polyester spacer knit serve as the inner filling. Each pad consists of two knitted faces connected by resilient monofilament strands, and the pads slip into sewn sleeves on either side of a rigid upright panel. The panel seats in a socket on the base, which sits in a pocket along the straight bottom of the cover. The knitted pads compress under contact and return to their original thickness when the load is removed.
The cover measures 250 mm high, 180 mm wide, and 85 mm deep. A centered steel plate measuring 170 mm by 75 mm by 6 mm sits inside a pocket sewn to the straight bottom. A rigid upright panel projects 210 mm above the plate, with foam filling on both faces and around the upper edge. The plate concentrates mass near the support surface and spreads the load across the bottom.
A modular display shelf has a steel rail recessed flush with its upper surface. Two permanent magnets recessed into the underside of the internal base attract the rail through the fabric at the straight bottom. A rigid panel rises from the base through the filling and holds the cover upright. Lifting the pillow releases it from the rail for repositioning.
An overhead camera captures the outline of each assembled rigid frame and base against a calibrated background. Image-processing software converts the frame outline into cutting paths for front and rear foam pads, including relief cuts at the base connection. A numerically controlled oscillating knife cuts the pads from foam sheet. The pads fit around the frame inside the cover, and a sewn bottom pocket retains the base.
A woven polyester gusset joins the front and rear panels around their edges. Its 70 mm wide lower segment follows the straight lower edge of each panel and forms the bottom of the cover.
A 3 mm thick steel plate with rounded corners slides into a close-fitting pocket sewn to the inside of the cover bottom. A zipper closes the pocket and holds the plate against the bottom panel.
Two blocks of flexible polyurethane foam follow the outlines of the front and rear faces. Relief slots in the inward-facing sides of the blocks fit around the frame uprights.
A bent steel tube forms two uprights and a rounded upper crossbar. Flattened feet at the lower ends bolt to the base, and fabric sleeves sewn inside the cover couple the upper portion of the cover to the crossbar.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The perimeter belt padding is sewn onto the panel padding, and the two lateral side padding portions form two lateral side walls of the cushion case, the bottom padding portion forms the bottom side wall of the cushion case, the lid padding portion forms the lid of the cushion case and is capable of being opened and closed, the top panel padding portion forms the top panel wall of the cushion case, and the base panel padding portion forms the base panel wall of the cushion caA · US 2009/0230007 A1 · abstract
The cover is preferably secured to the case along their perimeter edges, but may also include additional fastening within the perimeter's surface area.B · US 2016/0220048 A1 · ¶ 6
In an embodiment, a padding portion is made when cushion foam is inserted into and enclosed within the coat.A · US 2009/0230007 A1 · ¶ 29
Pillows and cushions are generally formed by encasing some form of filling in a sealed envelope.B · US 2016/0220048 A1 · ¶ 9
An empty cell means only that no passage was reproduced there.
But mobile computers are vulnerable to damage if dropped, bumped, compressed against other objects or otherwise impacted which often occurs during traveling or transporting.A · US 2009/0230007 A1 · ¶ 4
It can be adopted as a functional component by manufacturers of bag/pack/luggage which can be detachable or to be fixed within a bag/pack/luggage to serve as a protection component.A · US 2009/0230007 A1 · ¶ 8
This gives the user the option to simply change out the pillow case cover or cushion case cover as they desire; leaving the pillow case with pillow intact, or the cushion case with cushion intact.B · US 2016/0220048 A1 · ¶ 3
It will be apparent that both the cover and the correspondingly shaped case can be manufactured from natural, man made, or a combination of both materials; and that these materials can include natural, man made, or a combination of both: designs, scents, fragrances, coatings, layers and components.B · US 2016/0220048 A1 · ¶ 8
patent.fyi, US 2026/0354606 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354606/, SHA-256 c42e7438e0e9e78a9001ee9b1c6eaf49e6686ca27fb78dc0b8538f1e9bac1e77