1.1Screw mounted base
Two countersunk screws pass through an aluminum base and thread into a wooden window frame. A spring clip on the top face captures the flanges of the rail.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two countersunk screws pass through an aluminum base and thread into a wooden window frame. A spring clip on the top face captures the flanges of the rail.
One rectangular magnet sits in a recess in the bottom face and is magnetized across its thickness. A pair of iron plates conducts flux from the opposite poles to two contact faces that meet the steel mounting surface.
A glass-filled nylon base holds two rectangular magnets with their exposed pole faces flush with the bottom face. The exposed faces have opposite polarities, and the steel mounting surface carries flux between them.
A narrow lower tier houses the magnets and has vertical sidewalls. A horizontal ledge joins the lower tier to a wider upper tier that supports the rail clip.
The lower sidewall widens from the magnetic contact face toward the top of the base. A 2 mm radius joins the incline to the vertical peripheral side and ends at the full axial width.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A magnetic base with multiple magnets and iron plates seats against the underside of a steel cabinet shelf. An upper coupling carries a spring clip that grips both flanges of a cable support rail. The base widens away from its shelf contact face, and the inclined wall ends at a recessed step that provides a purchase point for tilting the base off the shelf.
Sintered strontium ferrite blocks replace the magnet inserts in the base. Each block sits in a pocket at the bottom face with one pole facing the steel mounting surface and the opposite pole against a low-carbon iron backing plate. The base widens toward the rail coupling, and the inclined wall ends at a recessed step. A spring clip on the coupling holds the rail.
An eccentric cam latch replaces the spring clip at the upper rail coupling. A fixed hook captures one rail flange, and a pivoting cam presses the opposite flange against a seat when the handle passes over center. Multiple magnets and iron plates hold the base against a steel mounting surface, and the inclined bottom wall widens toward a recessed shoulder. Rotating the handle back releases the rail while the base stays attached.
The base measures 40 mm across the bottom contact face and reaches a maximum axial width of 48 mm at the upper edge of two opposed inclined walls. Each wall rises 8 mm from the bottom face and ends at a shoulder that steps inward by 1 mm. Four 12 mm diameter disc magnets sit flush with the contact face in a two-by-two pattern, with an iron backing plate behind each disc. A 30 mm wide rail clip mounts at the center of the top face.
Clamp-on adapters grip the flanges of two suspended ceiling grid members and present flat steel landing plates beneath the grid. Each magnetic base seats against a landing plate, and its inclined bottom wall widens toward a recessed shoulder below the plate. The upper coupling on each base carries a swivel clip that grips the window covering rail and aligns it with the other clip.
Three spring-loaded contact pins sit in the bottom face between the magnet pockets, with one pin near each end and one near a lateral edge. Each pin actuates a sealed switch when a flat steel mounting surface presses the pin flush with the base. A controller in the upper rail coupling illuminates a green indicator when all three switches close and an amber indicator when any switch remains open. The inclined walls widen toward the coupling and terminate at recessed steps.
The bottom face spans 36 mm along the base axis and contains two recessed magnets. The sidewalls taper inward to a 28 mm top face that carries the rail clip.
Two rectangular magnets sit side by side in underside pockets with their downward poles oriented alike. One low-carbon iron plate spans the upper poles and bends down to the mounting face, while a second plate contacts the lower poles and presents a pole face flush with the first.
A stamped spring steel clip slides into a dovetail on the top face of the base. A fixed hook seats under one rail flange, and a spring arm snaps over the opposite flange. Pressing the release tab deflects the arm to free the rail.
Two milled end bevels widen the base axially from 24 mm at the bottom face to 32 mm at their upper edges. Each bevel ends at a horizontal shoulder that steps inward by 1 mm to the upper peripheral wall.
One axial end of a molded nylon base stays vertical while the opposite end slopes outward over a height of 5 mm. The slope increases the axial width from 26 mm at the bottom face to 30 mm at its upper edge, where a 0.8 mm inward step joins the upper peripheral wall.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In this embodiment of the invention, the panel's external edge 27 is beveled as is an internal edge 28 of the stepped shoulder. Further, the walls are beveled at the same angle so as to be parallel to one another.A · US 7,621,589 B1 · ¶ 24
Forming the cup to have a step shoulder comprises drawing metal from the inwardly tapering annular periphery of the cup, and collapsing the cup depth from the second cup depth to the third can body depth, metal drawn from the inwardly tapering annular periphery of the cup together with metal from collapsing the cup depth from the second cup depth to the third can body depth are sufficient to prevent the at least one axially extending side wall bead from extending into the steB · US 2011/0252858 A1 · ¶ 11
An empty cell means only that no passage was reproduced there.
More particularly, the invention relates to a panel used for building a sidewall of a large capacity walled enclosure without 5 the need for intermediate framing support.A · US 7,621,589 B1 · ¶ 1
A disadvantage of known panels for large capacity walled enclosures is that many require intermediate support posts.A · US 7,621,589 B1 · ¶ 6
More particularly, the present invention relates to a method for forming at least one rib and a step shoulder bottom of a can body in a single drawing operation from a redrawn cup which has a closed end with an inwardly tapering annular periphery including sufficient material to enable formation of the step shoulder bottom without having the at least one rib drawn into the step shoulder bottom.B · US 2011/0252858 A1 · ¶ 2
A problem that may be encountered when using draw-redraw forming techniques to form cans having step shoulders and axial ribs or beads in the side wall is that the axial ribs tend to be drawn into the step shoulder.B · US 2011/0252858 A1 · ¶ 7
patent.fyi, US 2026/0354610 A1, claim 1, first published 2026-11-19T00:49:41-05:00, https://patent.fyi/US20260354610/, SHA-256 639059b447b3de7c112fb98c90863f527983b9284ef5a9c199ed997b64395c43