1.1Rectangular body with flat base
Four stainless steel walls join at rounded corners around a flat rectangular base. The base conducts heat from a matching hot plate into the food compartment.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Four stainless steel walls join at rounded corners around a flat rectangular base. The base conducts heat from a matching hot plate into the food compartment.
Three raised pads on the body rim hold the cover 1 mm above the rim. Steam flows through the gap between the pads, and an overlapping cover skirt directs the flow downward.
A stainless steel tube with a 6 mm bore fits into the cover opening. The tube stays open during heating, allowing steam to discharge continuously at atmospheric pressure.
A stainless steel bracket supports a shallow water cup against the inner sidewall. An electric band heater on the outer wall transfers heat through the wall and bracket to the cup, and vapor rises from the open top.
A 300 mL reservoir sits on the inner bottom of a body with a 3 L first accommodation space. A heater below the base boils water in the reservoir, and steam passes through a perforated food tray above it.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A ceramics workshop uses a cylindrical container with a removable cover, a spring-loaded vent valve, and a shallow rectangular water tray clipped to the inner floor. A stainless steel rack above the tray supports moist clay test pieces during warming. An external heating plate warms the body, water evaporates from the tray, and the cover valve releases gas as pressure rises.
A cylindrical body holds a removable water cup against its inner floor, and a gasket seals the removable cover to the body. A food-contact silicone umbrella valve replaces the valve in the cover vent and snaps into a retainer with its flexible rim seated against the outer cover surface. Internal pressure lifts the rim to discharge gas through the vent, and the rim reseats as the pressure falls.
A shallow stainless steel reservoir clips to the inner floor of a cylindrical body beneath a raised rack. A removable porous alumina plate spans the reservoir opening, and two absorbent feet on the plate extend to the reservoir floor. The feet draw water into the plate by capillary action, the exposed plate surface releases moisture during heating, and a valve in the removable cover vents the headspace.
A cylindrical body has an internal diameter of 160 mm and an internal height of 200 mm, giving a main cavity of about 4 L. A removable rectangular reservoir with internal dimensions of 100 mm by 50 mm by 40 mm clips to one side of the inner floor and holds 200 mL at the brim, about one twentieth of the main cavity volume. During warming, water evaporates from the reservoir beneath a raised food rack, and a spring-loaded valve in the removable cover vents the cavity.
A cylindrical stainless steel body has a flat base bonded to a ferritic stainless steel plate and sits directly on an induction hob. A removable shallow water tray contacts the inner floor, and a perforated rack supports food above the tray. The hob heats the bonded plate, heat conducts through the floor and tray, and a spring-loaded valve in the removable cover vents the headspace.
A cylindrical container has a removable valved cover and a rectangular water tray on the inner floor above a separately controlled electric heater. A temperature and humidity probe rated for condensing conditions projects into the upper headspace through a sealed fitting. The controller calculates dew point from the probe readings, turns the tray heater on when the dew point falls 2 °C below the setpoint, and turns it off when the dew point reaches the setpoint. A separate heater regulates the container temperature.
A 0.8 mm stainless steel blank forms a cylindrical cup with a flat circular base and an open top. The cylindrical wall and base enclose the food compartment.
A rear hinge connects a domed cover to the upper body rim, and a front latch compresses a silicone gasket when the cover closes. A spring-loaded poppet seats in a through hole at the top of the dome and lifts when the internal pressure exceeds its opening setting.
A shallow stainless steel cup rests in a circular recess on the inner bottom surface. The cup holds 100 mL in a body with a 3 L first accommodation space, and heat from the base evaporates the water.
A cast aluminum boss projects from the inner bottom surface and contains a 40 mL water well in a body with a 1.2 L first accommodation space. The shared aluminum floor conducts heat from a heater below the body into the well.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The steam generator 60 comprises a housing or main body 70 in the form of a generally cylindrical tube. The main body 70 has an inside surface 72 that defines a steam generation chamber 74.A · US 2008/0040868 A1 · ¶ 36
Accordingly, the flour chamber is preferably configured similar in shape to an open top bowl, cup, or container with a cylindrical side wall and a bottom. The top of the flour chamber is open providing access to the internal aperture/compartment in the flour chamber.B · US 9,226,619 B2 · ¶ 16
The device further comprises a flip top lid hingedly connected to the food chamber (although a completely removable lid is also possible) and a handle on the exterior of the food chamber for grasping the food chamber and holding it with one hand.B · US 9,226,619 B2 · ¶ 14
An empty cell means only that no passage was reproduced there.
It is important that the steam generator has a sufficient amount of water to achieve a desired steam generation rate and to prevent damage to the steam generator.A · US 2008/0040868 A1 · ¶ 5
While these pressure and electrical conduction sensors provide a couple ways of controlling the supply of water to the steam generator, other possibly more economical, reliable, and elegant methods and structures for controlling the water supply to a steam generator of a fabric treatment appliance are desirable.A · US 2008/0040868 A1 · ¶ 5
Particularly in a commercial kitchen, such as a restaurant, the flouring and/or breading process needs to be done quickly.B · US 9,226,619 B2 · ¶ 6
A serious health risk is thereby created because the flour basin becomes contaminated between uses, especially when different foods are placed into the basin, such as, for example, certain types of raw foods, e.g., fish, beef, pork, and poultry.B · US 9,226,619 B2 · ¶ 7
patent.fyi, US 2026/0354611 A1, claim 1, first published 2026-11-19T01:26:01-05:00, https://patent.fyi/US20260354611/, SHA-256 2e4383e001b4ad924b5d6095b8ca9615a9253609042328e245bf83cee0b46a6f