1.1Separate brewing and collection vessels
Hot water enters the brew basket and wets the insoluble material. A mesh floor retains the solids as the beverage drains through a spout into the collection vessel.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Hot water enters the brew basket and wets the insoluble material. A mesh floor retains the solids as the beverage drains through a spout into the collection vessel.
A perforated basket hangs from the upper rim and supports the insoluble material inside the bore. A metering valve feeds hot water over the basket, and the beverage drains through the open lower end into a cup.
A removable curved panel exposes a side port wide enough to admit the filter plate edge first. The plate turns transverse to the vessel axis and couples to a rod guided by the top plate. The curved panel clamps flush with the bore, and a perimeter gasket seals the panel joint.
A fixed mesh disk covers a pickup at the bottom of the brew chamber. A hand-operated diaphragm pump draws liquid through the mesh and delivers it through an outlet check valve to the serving chamber.
A hand plunger seals against the inside wall of the basket and forces liquid through a mesh disk at its base. The outer vessel collects the beverage beneath the basket, and the gap around the basket vents displaced air.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A straight cylindrical vessel receives rinse water containing clay particles that settle at its closed bottom. A piston carries a supported fine filter cloth and two identical annular gaskets seated in axially spaced grooves around the filter. After settling, the operator lowers the piston until a rod stop holds it above the sediment, and water passes upward through the cloth. The operator decants the filtered water from above the piston into a container for the next rinse.
A sintered stainless steel disk serves as the filter element in a piston with two axially spaced silicone gaskets around its perimeter. A threaded retaining ring clamps the disk against a flat sealing washer on an internal shoulder of the piston. As the piston descends, liquid flows upward through the interconnected pores in the disk and larger particles remain below it.
Two identical food-contact silicone U-cup seals serve as the sealing gaskets in separate circumferential grooves around the piston filter. Both cup openings face the closed end of the vessel, and their outer lips contact the cylindrical wall when the piston is inserted. On the downstroke, pressure below the piston acts inside the lower cup and urges its outer lip against the wall. Liquid passes through the central filter, and the upper cup seals against any liquid that enters the space between the cups.
A straight cylindrical vessel has a 100 mm internal diameter and a 200 mm internal depth. The piston carries three identical silicone gaskets in circumferential grooves spaced 8 mm apart from center to center along the axis. A rod stop keeps the underside of the filter 25 mm above the closed end at the bottom of the stroke. During the downstroke, the gaskets seal against the vessel wall and liquid passes through the central filter into the space above the piston.
An electrically heated dispensing base supports the vessel and transfers heat through its closed bottom. The vessel has a side outlet connected to a manual dispensing valve, and the outlet sits above the upper gasket when the piston reaches its lower stop. After steeping, the operator lowers the piston so the beverage passes upward through the filter. With the piston held at the stop, opening the valve drains the filtered beverage by gravity.
A motor-driven lead screw lowers a guided piston rod into the vessel, and a load cell between the drive carriage and the rod measures axial force. The piston carries a central filter and two axially spaced gaskets that contact the vessel wall during the stroke. The controller reduces the descent speed when the measured force exceeds a preset threshold and stops the drive if the force reaches a higher limit. A lower travel switch ends the normal stroke while leaving room for the collected solids beneath the filter.
A deep-drawn stainless steel cup has an integral closed base and a rolled rim at its open end. The cylindrical bore guides the piston and holds the liquid and insoluble material during steeping.
A stainless steel rod threads into the center of the filter assembly and slides through a bushing in the removable lid. The assembly enters through the vessel mouth and travels toward the base when the user pushes the handle.
Two silicone O-rings sit in separate circumferential grooves on the outer rim of the filter carrier. The groove centers are 6 mm apart along the vessel axis, and both rings compress radially against the bore.
A stainless steel mesh disk with 200 µm openings rests on a perforated support plate inside an annular carrier. Two axially spaced silicone lip gaskets seal the carrier against the vessel wall and direct flow through the mesh.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Flavored particles C, T and water W may be placed within the brewing vessel 300 with the flavored particles fully immersed in the water W.A · US 2017/0367520 A1 · ¶ 33
The infusion device 10P comprises an essentially cylindrical container 20 with a longitudinal axis L and with an open end 22 and a closed end 24.B · US 2018/0289200 A1 · ¶ 37
After the insoluble material 37 has been allowed to interact with the water for the desired amount of time, the piston-filter arrangement 26 is inserted into the container 20 via the open end 22 and the filter press 30 is pressed by means of the piston rod 28 along the longitudinal axis L toward the closed end 24 of the container 20 (see FIG. 1a)).B · US 2018/0289200 A1 · ¶ 38
The filter press has a shape corresponding to the cross section of the container, so that the filter press forms a seal with the container on the side.B · US 2018/0289200 A1 · ¶ 3
An empty cell means only that no passage was reproduced there.
However, leaving the water in the brewing vessel for time periods longer than desired may result in “over-brewed” coffee or tea that has an unpleasant taste.A · US 2017/0367520 A1 · ¶ 3
In embodiments, the full immersion brewer may be a press brewer with a press filter and a weight configured to apply a downward force on the press filter via the force of gravity.A · US 2017/0367520 A1 · ¶ 8
In particular, if a relatively large amount of insoluble material has been used, the insoluble material must be compressed so that the filter press can be inserted into the collection receptacle, which can require a relatively large amount of force.B · US 2018/0289200 A1 · ¶ 7
This configuration significantly simplifies the cleaning of the container.B · US 2018/0289200 A1 · ¶ 5
patent.fyi, US 2026/0354615 A1, claim 1, first published 2026-11-19T01:26:01-05:00, https://patent.fyi/US20260354615/, SHA-256 61b2a909cf3ae64495ff86c98f574c1ee53239f422e44d12dcae56eb7e51c731