1.1Spray and vacuum cleaning
A diaphragm pump feeds overlapping fan jets that wash a strip of glass as the device passes. A vacuum slot held 1 mm off the glass draws spent liquid into a separator tank.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A diaphragm pump feeds overlapping fan jets that wash a strip of glass as the device passes. A vacuum slot held 1 mm off the glass draws spent liquid into a separator tank.
Two cables from motorized drums above the pane set the position of a separate wiping carriage. The carriage controller follows the housing position with a fixed lag, and an onboard suction chamber draws a spring-loaded microfiber pad against the glass.
A motorized drum rides on a horizontal rail above the pane and winds or pays out a cable fastened to the housing. The rail carriage sets the horizontal position, while the walking belt feeds at the housing travel speed during each vertical pass.
Each roller has a molded silicone tread and its own geared motor. Spring-loaded bearing carriers distribute the suction load between the rollers, and the controller synchronizes their surface speed with the walking wheel.
A toothed wheel engages the inner face of the belt at one end, and the belt slides around a curved low-friction polymer shoe at the other. A slotted shoe mount sets belt tension, and the straight run between the wheel and shoe presses against the glass.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A crawler wipes the cover glass of framed photovoltaic modules installed in a tilted row. The housing carries a driven walking wheel and a driven belt looped around two housing-mounted pulleys. A spring-loaded microfiber pad spans the housing behind both traction contacts and wipes the glass dry as the crawler traverses each module. Pairs of hook rollers at the ends of the housing capture the upper and lower frame lips and retain the crawler on the tilted surface.
An articulated track of acetal links with molded silicone pads replaces the continuous walking belt. The track loops around two housing-mounted sprockets, and a slotted axle mount sets the tension at the idler sprocket. A stationary backing rail supports the glass-facing run so that several pads share the contact load. The driven sprocket and a separate driven walking wheel propel the housing while a trailing cloth wipes the glass.
A straight silicone squeegee blade replaces the cloth wiping pad and sits across the travel direction behind the walking wheel and belt. A carriage runs on two transverse guide rods, and a motor-driven eccentric moves the carriage 8 mm from end to end at 5 Hz. Two compression springs press the blade carrier toward the glass, and a spray bar wets the glass immediately ahead of the blade. The walking wheel and two-pulley belt propel the housing while the blade reciprocates laterally and pushes liquid toward a collection lip.
A 35 mm wide walking belt runs around two 30 mm diameter end pulleys spaced 120 mm apart on the housing. Two 20 mm diameter backing rollers sit inside the belt loop at 40 mm intervals along the glass-facing run and support it under load. A separate 40 mm diameter walking wheel carries a spring-loaded mount that presses it against the glass. The wheel and driven end pulley are set to a nominal surface speed of 50 mm/s, and a trailing wiper spans 160 mm across the travel direction.
A roof-mounted facade maintenance gantry carries a powered winch and a traversing cable trolley. The cable attaches to a central lifting point on the crawler housing through an in-line load cell, and the winch maintains a preset support tension as the crawler changes height. The trolley follows the crawler laterally to keep the cable close to vertical. A driven walking wheel and a driven two-pulley belt move the housing across the pane while a spring-loaded wiping pad presses against the glass.
An encoder measures the speed of the walking wheel, a second encoder measures the speed of the belt drive pulley, and a spring-loaded passive measuring roller senses housing travel against the glass. The controller converts the three signals to linear speeds using their effective rolling radii. During straight wiping passes, it reduces the motor current limit for either drive whose surface speed exceeds measured travel speed by more than 15 percent for 100 milliseconds. It restores the current limit in steps once the speed difference falls below 5 percent.
A removable microfiber pad fastens to a platen carried on four compression springs. The springs distribute contact pressure across the pad and let the platen follow small changes in the glass surface.
A 35 mm walking wheel has a molded silicone tread bonded to an aluminum hub. A geared motor turns the hub on a shaft supported by two bearings seated in the housing.
A 25 mm wide polyurethane belt loops around a toothed drive wheel and an adjustable idler wheel. Aramid cords limit stretch, and a silicone outer tread forms the contact surface against the glass.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A mounted wiper system comprising: (a) at least one wiper blade; wherein the wiper blade allows for bi-directional wiping movements; wherein the wiper blade touches the longitudinal length of the planar surface; wherein the wiper blade is held in place by the blade housing;B · US 2015/0020337 A1 · claim 1
In the movable-body linear drive assembly, when the stepping motor 2 rotates the drive pulley 6, the belt 14 is entrained about the pulleys 6, 12 to circulate in a first direction indicated by arrow M in FIG. 1, and the movable body 16 linearly moves in a second direction opposite to the first direction.A · US 2005/0064971 A1 · ¶ 21
An idler pulley 42 is disposed such that the idler pulley 42 is spaced from the drive pulley 36 by a distance, and a sheet belt 44 is wound around these pulleys 36, 42 to be circulated by the pulleys 36, 42. A movable body 46 is mounted on the belt 44, whose linear movement is guided by a guide 48.A · US 2005/0064971 A1 · ¶ 27
An empty cell means only that no passage was reproduced there.
However, the providing the monitor signal generating means separately from the linear drive assembly makes the structure of the assembly complex and pushes up the manufacturing cost also.A · US 2005/0064971 A1 · ¶ 7
Thus, the assembly is simplified in structure, requires a reduced manufacturing cost, and is capable of monitoring the movement of the movable body.A · US 2005/0064971 A1 · ¶ 10
The present invention is a built-in wiper system designed to wipe single and multiple parallel planar surfaces when at least one of the plane is slid open or close.B · US 2015/0020337 A1 · ¶ 11
This invention eliminates the frequent need to manually squeegee or wipe liquid from glass, plastic, or tiled panes from sliding shower enclosures, sliding windows, and sliding doors.B · US 2015/0020337 A1 · ¶ 11
patent.fyi, US 2026/0354634 A1, claim 1, first published 2026-11-19T01:26:01-05:00, https://patent.fyi/US20260354634/, SHA-256 58c77cd823a92c18e2c77857a04c22ba37ec47c913716f3ae9aa29a0c12068d6