1.1Ramp with one-sided flare
The straight inboard side runs parallel to the cleaner base. The outboard side widens from 12 mm at the nose to 35 mm at the rear, increasing the width of the surface that supports the rug as the nose passes beneath it.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The straight inboard side runs parallel to the cleaner base. The outboard side widens from 12 mm at the nose to 35 mm at the rear, increasing the width of the surface that supports the rug as the nose passes beneath it.
Three polymer standoffs molded into the ramp support the underside of the magnet. A shoulder screw through the magnet retains it with 0.2 mm of axial clearance, allowing it to turn on the standoffs.
Two spring steel jaws spread as the clip presses over the rib and close behind its shoulders. The clip carrier turns around a shoulder screw fixed to the ramp, and two release tabs open the jaws for removal.
The pin passes through the magnet and cap, and its serrated lower end is pressed into a matching bore in the ramp. A swaged head and a low-friction washer retain the magnet and cap with enough axial clearance for them to turn.
A flush floor insert has an open channel that extends from the exposed floor beneath the rug edge. Narrow ribs hold the rug at floor level while a gasketed vacuum nozzle seals over the exposed end of the channel and draws air and loose debris from beneath the rug into the cleaner.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A ramp with mirrored profiles mounts to the steel side panel of a walk-behind stall scraper. A screw passes through the cap and circular magnet and threads into the ramp, and a shoulder on the screw leaves the cap and magnet free to turn. As the scraper travels along a loose stall mat, the ramp enters beneath the mat edge and raises it ahead of a scraper blade that collects bedding from the exposed strip.
A padded over-center edge clamp replaces the circular magnet and grips a flange on the cleaner base. The fixed jaw carries a cap with a flanged bushing, and a shoulder screw passes through the bushing and threads into the ramp. Closing the lever fixes the clamp to the flange while the ramp and screw pivot together in the bushing.
A 100 mm long, 24 mm wide ramp has two 50 mm approaches rising from 0.8 mm thick tips to a central surface 6 mm above the floor. A 16 mm diameter circular magnet sits in the cap, and an M4 shoulder screw passes through both parts into the side of the ramp. The shoulder provides 0.3 mm of axial clearance for rotation, and either tip feeds under the mat during a pass along its edge.
A symmetric ramp attaches to a steel plate on the cleaner base by a cap that houses a circular magnet around a shoulder screw fixed to the ramp. A lateral duct branches from the main suction passage and terminates in a slot beside the ramp, between its fore and aft tips. As either tip lifts the rug edge, the slot draws debris from the exposed strip into the main suction passage.
A vertical linear guide on the cleaner base carries a steel plate, and a compression spring biases the plate toward its lower stop. The ramp assembly attaches to the plate by a cap containing a circular magnet, with a shoulder screw fixed to the ramp and free to rotate in the cap. A small floor roller mounted below the plate lifts the guide carriage onto raised thresholds, and the spring returns the carriage as the roller follows the floor downward.
A circular magnet holds the cap on a steel side plate, and a shoulder screw keyed to the ramp turns in the cap. A geared motor carried by a bracket on the cap drives a sector gear fixed to the ramp, and a rotary encoder reports the ramp angle. A downward-facing optical range sensor views the rug edge ahead of the ramp, and the controller limits travel speed and sets the encoder target from a calibrated table of edge heights and ramp angles. When the sensor detects bare floor beyond the edge, the controller returns the ramp to its raised travel position.
A molded nylon ramp has a central crest 12 mm high and matching 50 mm slopes descending to opposite ends. Its plan outline mirrors across the longitudinal centerline, and its longitudinal vertical profile mirrors across the plane through the crest.
An axially magnetized ring sits in a circular recess in a molded nylon cap. Its central bore receives the retaining screw, and its exposed pole face contacts a flat steel plate on the cleaner base.
A rounded stainless steel nose enters beneath the rug edge 1 mm above the floor. As the cleaner moves forward, the edge travels up a 65 mm slope to a height of 12 mm, opening a gap for airflow beneath the rug.
A steel shoulder screw seats against a brass threaded insert in the ramp and stays fixed as the cap turns. A polymer sleeve in the cap rides on the smooth screw shoulder, and locating tabs hold the circular magnet so it turns with the cap.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The magnet 316 is positioned in a bottom of the magnetic cup, i.e., on a surface of the base magnetic plate 304a opposite the planar outer surface.B · US 10,531,202 B1 · ¶ 53
A vehicular safety ramp apparatus has a ramp including an inclined ramp surface for progressively elevating a front wheel of a vehicle above a surface on which the ramp is positioned.A · US 2011/0049447 A1 · abstract
According to another aspect of the invention, a hinge having a first hinge leaf is mounted to the ramp and a second hinge leaf is pivotally mounted to the first hinge, with the web attached thereto, by a removable pin for removal and storage of the strap/web.A · US 2011/0049447 A1 · ¶ 9
An empty cell means only that no passage was reproduced there.
Therefore, there exists a need for improved ramps and methods for raising and lowering vehicles without movement of the ramps.A · US 2011/0049447 A1 · ¶ 5
The web is adapted for being placed under the rear wheel whereby the weight of the rear wheel locks the ramp in a fixed position as the front wheel is progressively elevated and lowered along the ramp surface.A · US 2011/0049447 A1 · ¶ 7
An actuator, e.g., used to generate sound, may include a suspension that is part of a magnetic cup to reduce a depth of the actuator.B · US 10,531,202 B1 · ¶ 2
The magnetic cup may include one or more joint elements (e.g., a rabbet or a chamfered, scalloped, or filleted edge) at the edge of the base into which the suspension fits.B · US 10,531,202 B1 · ¶ 3
patent.fyi, US 2026/0354637 A1, claim 1, first published 2026-11-19T01:26:01-05:00, https://patent.fyi/US20260354637/, SHA-256 d45214779096e65542e23e6c8e771badf111d6da7c70a0e268494ac1a9f2316f