Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
1.1Forward loop for repeat scrubbing
What ifWhat if the robot made a forward loop to scrub the detected patch again?
Claim language“move in a backward manner”
The controller records the patch coordinates and uses the two drive wheels at different speeds to steer through a loop with positive forward speed. It aligns the mop with the recorded patch on reentry and slows the chassis as the mop crosses it.
1.1Sensor guided reverse scrubbing
What ifWhat if live soil readings governed the reverse pass one control cycle at a time?
Claim language“based on a preset cleaning path”
A floor-facing optical sensor array samples the floor just ahead of the mop in the reverse travel direction. At each control cycle, the controller adjusts the two wheel speeds to center the strongest soil reading under the mop and ends the pass after readings across the array remain below a threshold for 0.5 seconds.
1.2Mop and wheel counterrotation
What ifWhat if the mop roller turned opposite to the drive wheel during reverse travel?
Claim language“a rotation direction of the driving wheel is the same as that of the mop”
An independent motor turns the roller so its floor-facing surface sweeps in the direction of reverse chassis travel. A spray bar wets the roller, and a scraper strips the collected liquid and soil into a recovery trough.
1.2Fixed roller spans wheel tracks
What ifWhat if a fixed transverse roller already spanned both wheel tracks throughout the reverse pass?
Claim language“adjusting the mop to be located at a first position”
Fixed bearing mounts hold a 300 mm active roller across drive wheels with a 270 mm outside-to-outside span. The controller guides the chassis straight backward across the patch so the trailing wheel tracks lie within the wetted strip swept by the roller.
Section 2 · machine-generated
Variations
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Other field of use
Reverse scrubbing for greenhouse aisles
A greenhouse aisle scrubber carries a powered roller behind its drive wheels and uses a downward-facing camera to detect patches of spilled potting mix on sealed concrete. When the camera detects a patch during forward travel, the controller follows a preset sequence that passes the patch and retraces the aisle centerline in reverse. Before reversing, a lift actuator lowers the roller to the floor, where its working width spans both wheel tracks. During the reverse pass, the wheel and roller shafts turn in the same direction when viewed from the same side of the chassis.
Component substitution
Hydraulic motor for roller drive
A reversible gerotor hydraulic motor replaces the electric mop motor and couples directly to a roller mounted behind the drive wheels. An electric pump supplies fluid through a directional valve, and a separate lift actuator lowers the roller to a working height where its contact strip spans both wheel tracks. When the controller starts the preset reverse pass over a detected soil patch, it shifts the valve to match the wheel rotation direction as viewed from the same side of the chassis. A flow control valve sets roller speed independently of travel speed.
Parameter or scale variation
Wide roller with phased reverse passes
A floor scrubber has a 700 mm roller mounted behind two drive wheels whose outer edges are 620 mm apart. A four-bar linkage lowers the roller to the working position before each reverse pass, leaving 40 mm of roller width outside each wheel track. For a detected soil patch, the controller chooses a preset two-pass pattern with parallel reverse paths spaced 500 mm apart, producing 200 mm of overlap. The robot reverses at 0.15 m/s on each pass while the roller turns at 180 revolutions per minute in the same direction as the wheels when viewed from the same side.
Combination with existing systems
Reverse cleaning with floor recovery
A roller mounted behind the drive wheels scrubs the floor, and a full-width vacuum squeegee mounted ahead of the wheels collects liquid as the chassis reverses. The squeegee has a floating mount and a suction hose connected to a recovery tank. When the controller detects a soil patch during forward travel, it starts a preset reverse pass, lowers the roller and squeegee, and runs the vacuum blower. The roller spans both wheel tracks and turns in the same direction as the wheels when viewed from the same side, while the squeegee collects liquid after the wheels pass.
Automated or data-driven variant
Optical selection of reverse passes
A downward-facing camera and a fixed light source ahead of the drive wheels capture floor images during forward travel. The controller compares image regions with a clean-floor reference for the current floor type and records patches whose contrast exceeds a stored threshold across three consecutive frames. Wheel encoders and image calibration locate each patch on the floor map, and the controller selects a preset reverse pattern whose roller footprint covers the mapped patch. A lift actuator lowers the roller behind the wheels so it spans both wheel tracks, and the controller commands matching wheel and roller rotation directions as viewed from the same side.
Sensor feedback for mop position
A roller spans both wheel tracks behind the drive wheels and rides on a pivot arm at each end. Load cells at the roller bearings measure contact force, and two linear actuators adjust the arm positions independently. After a soil sensor triggers a preset reverse pass, the controller lowers the roller until both load cells reach their target values and adjusts each end during travel to follow shallow floor height changes. Encoders report wheel and roller rotation, and the controller maintains matching directions as viewed from the same side of the chassis.
Specific version of a part
Stored straight reverse pass
A floor-facing reflectance sensor flags a soiled patch during forward cleaning. The controller executes a stored maneuver that advances 120 mm and then reverses 300 mm along the same heading at 60 mm/s, with encoder feedback keeping the roller on the patch.
Slide positions roller over track
A lead screw shifts the roller assembly 25 mm sideways to a limit switch at the first position, where the active roller surface overlaps the full tire width. During the straight reverse pass, the separate wheel and roller motors turn both shafts in the same angular direction when viewed from the same side of the chassis.
Cite aspatent.fyi, US 2026/0354645 A1, claim 1, first published 2026-11-19T01:26:01-05:00, https://patent.fyi/US20260354645/, SHA-256 091e5f353dd8978db0345a162e8dd2fa9c1e18d424e0f0f1de86ea3923d88437