1.1Integral lens seat
The bore centers the lens rim, and a machined shoulder sets the axial position. A retaining ring presses the rim against the shoulder, and the camera carriage moves the lens and camera together.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The bore centers the lens rim, and a machined shoulder sets the axial position. A retaining ring presses the rim against the shoulder, and the camera carriage moves the lens and camera together.
A hook on the latch engages a transverse pin on the bracket base. Closing the lever draws the bracket against its locating surfaces and moves the linkage past dead center, where clamp tension holds the lever closed.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An overhead inspection station uses a bracket arm to hold a close-up lens between a camera and a printed circuit board. A conical socket and a radial V-groove on the bracket base receive two spherical studs on the plinth, and a flat pad on the base rests on a third stud. A magnet on the plinth draws a steel plate on the base toward the three seats and holds the lens on the camera axis during board imaging.
A spring-loaded over-center draw latch replaces the magnet. The latch pivots on the plinth and hooks onto a transverse pin on the bracket base. Closing the latch pulls the base against a flat seating face while a round locating pin and a diamond locating pin engage two cylindrical bushings to set lateral position and rotation.
A split spring-steel collet in the plinth receives a ground cylindrical pilot on the bracket base in place of the paired lugs and tapered notches. The collet centers the pilot as it enters, and a separate dowel engages a radial slot to set the angular position. A magnet on the plinth pulls a steel keeper on the bracket until an annular shoulder on the base contacts the plinth face and sets insertion depth.
A 24 by 20 millimeter plinth mates with a bracket whose 35 millimeter arm carries an 18 millimeter diameter lens. A 3 millimeter round pin and a 3 millimeter diamond pin sit 14 millimeters apart on the plinth and enter chamfered bushings in the bracket base. A magnet on the bracket draws the base onto three coplanar pads with a measured pull-off force of 6 to 8 newtons at the seated position.
The plinth bolts to the moving carriage of a motorized linear stage mounted on the camera frame, with stage travel parallel to the camera optical axis. A round pin and a diamond pin locate the bracket base on the carriage, and a plinth magnet holds the base against the carriage seating face. The stage moves the fundus lens along the optical axis while the camera remains stationary, and limit switches bound carriage travel.
Three spring-return plungers sit beside three seating pads on the plinth, and each plunger operates a microswitch set to close within the final 0.2 millimeter of travel. A round pin and a diamond pin guide the bracket base into position, and a magnet draws it against the pads. The camera controller enables image capture when all three switches stay closed for at least 100 milliseconds and disables capture when any switch opens.
A flange at the rear of the tube attaches to the carriage, and an annular shoulder at the front supports the lens rim. The tube bore clears the marginal rays across the camera's field of view.
Two adhesive pads join a flat on the lens rim to the arm face outside the clear aperture. A removable fixture sets the lens center and tilt while the adhesive cures.
The camera images two fiducials on the lens rim and displays their offsets from calibrated target positions. The operator slides and rotates the base on the plinth until the fiducials coincide with the targets, then locks the base with a downward clamp.
A split aluminum ring at the arm tip seats the lens rim against an internal shoulder. A tangential screw closes the split and compresses a polymer liner around the rim.
Three hardened steel balls on the bracket base contact a conical recess, a V-groove, and a flat pad on the plinth. A preload normal to the plinth holds the balls against the six contact points that locate the base.
A permanent disk magnet sits in a blind bore in the plinth and pulls on a low-carbon steel plate fixed to the bracket base. Locating pads set the face gap and carry the contact load.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The rotor drive pins 44 are insertable into complimentary rotor drive sockets 46, shown in FIG. 4, in the rotor disc 24. The rotor drive pins 44 and rotor drive sockets 46 are configured to properly locate the magnet support band 30 to the rotor disc 24 and to efficiently transfer rotational energy from the rotor disc 24 to the magnet support band 30 during operation of the electric machine 10.A · US 8,089,189 B2 · ¶ 17
The second bracket part 6 is attached to the inner surface of the plinth, as shown in FIG. 3c. The plinth 48 and end panel 44 are brought together and protrusion member 26 of second bracket part 6 is located in the recess 20 defined between the lower surface of the first bracket part 4 and the end panel.B · US 2012/0132774 A1 · ¶ 76
An empty cell means only that no passage was reproduced there.
Attachment of the permanent magnets to the rotor via adhesives, however, subjects the magnets to high loads during operation of the electric machine leading to damage and/or failure of the permanent magnets and the electric machine.A · US 8,089,189 B2 · ¶ 2
Although the following description refers almost exclusively to a bracket assembly for allowing a furniture plinth to be attached to an end panel of a furniture unit, such as in a domestic kitchen, it will be appreciated that the bracket assembly can be used for connecting any two or more items together in any suitable application, either in an external and/or internal joint.B · US 2012/0132774 A1 · ¶ 2
It is an aim of the present invention to provide a bracket assembly which provides a snug fit and improved alignment between two or more items being joined together via the bracket assembly.B · US 2012/0132774 A1 · ¶ 7
patent.fyi, US 2026/0354682 A1, claim 1, first published 2026-11-19T02:03:35-05:00, https://patent.fyi/US20260354682/, SHA-256 4c6b4080b2c540673fadb9285f70e68439d8cdcc962ee68ed7f5eb45b31fd968