1.1Permanently sealed handle
Ultrasonically welded housing halves enclose a carriage that rides on molded rails. An elastomer boot bonded to the housing and thumb slider flexes as the carriage drives the distal wire.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Ultrasonically welded housing halves enclose a carriage that rides on molded rails. An elastomer boot bonded to the housing and thumb slider flexes as the carriage drives the distal wire.
A thumb dial and grooved drum turn together about a fixed transverse pin. Turning the dial draws the wire into the handle, and a distal return spring draws it back out as the dial reverses.
The guide rod passes through a longitudinal bore in the actuator. Staked rod ends anchor it to the main body, and fixed shoulders limit actuator travel in both directions.
The sheath ferrule seats against a shoulder inside the distal socket. A U-shaped spring clip slides across the socket into an annular groove in the ferrule and withdraws sideways to release it.
The plain wire end enters a straight groove in a clamp block carried by the actuator. Closing an eccentric lever presses a serrated shoe against the wire so the block transfers axial force, and opening the lever releases the grip.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handpiece operates a cable-driven gripper that retrieves loose fasteners from enclosed machinery. The collet grips a rigid ferrule crimped onto the proximal end of the gripper sheath, and the enlarged cable end seats in the sliding actuator coupling. Pulling the actuator closes the spring-open jaws, and releasing it lets the jaws reopen. Loosening the collet nut and opening the actuator coupling frees the gripper and its cable as a unit.
A bayonet socket at the distal end of the handle body replaces the collet and collet nut. Two radial pins on the sheath ferrule enter axial slots in the socket and turn into circumferential pockets behind the socket face. A spring washer biases the pins into recesses at the ends of the pockets, and a central bore passes the wire to the sliding actuator coupling. Pressing the ferrule inward and reversing the turn releases the sheath.
A hinged stainless steel gate on the sliding actuator closes over a side-loading pocket that accepts a spherical proximal wire end. The pocket has opposed axial bearing faces that transfer push and pull loads to the sphere, and a narrow distal slot passes the wire. An external tab opens the spring-loaded gate so the wire end lifts out sideways. A captive transverse pin separately releases the actuator from a longitudinal guide rod fixed to the handle body.
A retrieval basket uses a 1,200 mm sheath with a 2.4 mm outside diameter and a 0.45 mm diameter control wire with a 1.5 mm diameter proximal bead. The collet grips the sheath ferrule, and the actuator coupling captures the bead between axial bearing faces. An adjustable stop on a 1 mm pitch screw sets actuator travel from 4 to 12 mm, measured from a fixed proximal stop. Distal travel pushes the basket out of the stationary sheath, and proximal travel retracts it.
A flexible sampling forceps passes through the working channel of an endoscope, and a support bracket clamps to the endoscope grip beside the channel inlet. A sliding cradle on the bracket supports the forceps handle and locks at the selected insertion depth. The handle collet anchors the sheath, and the separate actuator coupling transmits motion through the enlarged wire end to open and close the sampling jaws. The cradle holds the insertion depth as the operator cycles the jaws.
A stepper motor and lead screw translate the actuator inside the handle, and a linear encoder measures actuator travel relative to the handle body. A miniature load cell between the actuator and the releasable wire coupling measures wire tension while the collet anchors the sheath. The controller retracts the wire to close the sampling jaws and stops when tension reaches a preset limit or the encoder reaches the programmed end of travel. An opening command drives the actuator back to a home switch, where the wire coupling aligns with a service opening for removal.
Two injection-molded polycarbonate shells form the main body and seat against molded locating pins. Captive screws hold the shells together and release them for disassembly.
An acetal thumb slider rides on two longitudinal rails molded into the main body. Stop faces at the ends of the rails define an 8 mm stroke.
A threaded carrier screws onto the distal end of the main body and houses a stainless steel collet with four slotted fingers. Tightening the collet nut drives its internal taper over the fingers and compresses them around the sheath.
A stainless steel ball terminal swages onto the proximal end of the wire and drops into a side-entry pocket in the first coupling device. A sliding gate closes the entry while opposed pocket shoulders transmit axial force between the terminal and the coupling device.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The transverse sliders 1a to 1e are disposed to be movable relative to the vacuum chamber top 3 and relative to the longitudinal sliders 2a to 2h in a direction parallel to the direction of transport T.B · US 10,106,349 B2 · ¶ 29
The collet 31 of the boot collet 30 compresses onto the armor sheath 22 of the armored fiber optic cable (see FIG. 3) when the collet nut 40 is tightened onto the boot collet 30. The camming surface 32 of the boot collet 30 interacts with the collet nut slope 42 of the collet nut 40 when the collet nut 40 is tightened onto the boot collet 30 (via the interaction between the boot collet threads 33 and the collet nut threads 43) in order to compress the collet 31 onto the armor sheath 22.A · US 2015/0030303 A1 · ¶ 14
An empty cell means only that no passage was reproduced there.
Often with the use of armored fiber optic cable 20, the interior fiber cable 24 will need to extend past the end of the armor sheath 22 of the cable, such as when the fiber cable is terminated within an enclosure.A · US 2015/0030303 A1 · ¶ 2
However, since the armor sheath 22 is generally tough and stiff and the interior fiber cable 24 is flexible and compliant, sharp bends can be induced on the interior fiber cable 24 at the exit point of the armor sheath 22.A · US 2015/0030303 A1 · ¶ 2
It is accordingly an object of the invention to provide a sheet-transporting element with an integrated blocking slider for suction openings, which overcomes the hereinafore-mentioned disadvantages of the heretofore-known devices of this general type and which has a high degree of operational reliability.B · US 10,106,349 B2 · ¶ 5
The different sheet formats may also be formats of different orientation, namely portrait and landscape formats, which have identical print sheet sizes.B · US 10,106,349 B2 · ¶ 8
patent.fyi, US 2026/0354805 A1, claim 1, first published 2026-11-19T04:13:02-05:00, https://patent.fyi/US20260354805/, SHA-256 cbf90a11a93ea534f3e7000fb16b38b26cd3e3ad19178247ef1605880ea8a15c