1.1Supports on separate rails
Each finger has a proximal hinge pin seated in a rail clamp. Sliding the two clamps along their respective rails sets the starting positions of the fingers relative to the surgical field.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each finger has a proximal hinge pin seated in a rail clamp. Sliding the two clamps along their respective rails sets the starting positions of the fingers relative to the surgical field.
An axial carriage advances each finger along its length, and a transverse carriage sets the spacing between the fingers. Hand knobs turn lead screws that move the carriages while the guides maintain finger orientation.
Opposed silicone pads seat in recesses halfway along the fingers. Closing the fingers brings the pads into contact with the shaft, and compliant mounts distribute the load across the pad surfaces.
Two planar paddles pivot on pins and pull a cable linked to the fingers when squeezed together. A flat release lever disengages the holding mechanism, and a return spring opens the fingers.
The rod slides freely through the clutch as the fingers close. Reverse load wedges the rollers between the rod and tapered pockets, and a release collar moves the rollers clear so the rod can slide back.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A retractor body clips to a reinforced edge of a flexible bench mat beside a wiring fixture. Two fingers with transverse and longitudinal pivots carry smooth, concave pads that cradle a jacketed cable. Squeezing two recessed controls advances a gear and pawl to hold the cable clear of the wiring fixture while terminals are installed. Lifting the pawl permits the controls to spread the fingers and release the cable.
A roller clutch replaces the gear and pawl on a transverse shaft that drives both fingers through opposed crank links. The clutch outer race seats in the body, and the inner race turns with the shaft during closure. Reverse torque wedges the rollers between the races and holds the finger position. A release lever moves the roller cage away from the wedging position so a return spring opens the fingers.
Two smooth polyurethane bladders replace the distal gripping pads and seat in shallow recesses in rigid carriers. A small-bore tube connects the bladders into a sealed saline circuit with a spring-loaded piston accumulator mounted in the body. When one bladder compresses, fluid flows into the opposite bladder and the accumulator, allowing the contact surfaces to conform as the fingers close. The accumulator piston displaces fluid back into both bladders when the fingers open.
Each finger has three pivots arranged in series for lateral swing, closing motion, and distal pad tilt. Mechanical stops limit lateral swing to 15 degrees on either side of center and pad tilt to 10 degrees on either side of neutral. A 72-tooth ratchet advances a common drive shaft by 5 degrees per tooth, and a 4-to-1 reduction turns each closing pivot by 1.25 degrees per step. The other two pivots remain adjustable as the ratchet holds the closing angle.
A clamp mounts an articulated support arm to the side rail of an operating table. The distal end of the arm docks into a socket on the retractor body through a keyed pin, and a separate clip attaches the body to the drape. The arm joints adjust the height and orientation of the body and transfer steady traction loads to the table when tightened. The finger ratchet adjusts grip independently of the arm joints.
A miniature load cell sits between each distal pad and its carrier, and a geared motor drives the common closing shaft one ratchet tooth at a time. A controller samples both load cells after each step and stops the motor when either pad reaches its programmed force threshold. An independent hardware comparator cuts motor power if either sensor signal exceeds a separate maximum threshold. A manual lever lifts the pawl and disengages the motor coupling so a return spring opens the fingers.
Each finger incorporates two pin hinges with perpendicular axes. The proximal hinge changes the height of the distal end, and the second hinge changes its lateral position.
A broad silicone pad sits on a guided spring plunger at each finger tip. The pad deforms to spread the contact load, and a stop on the closing linkage limits spring compression and the resulting gripping force.
A concave thumb cup and a concave finger cup sit on the ends of opposed pivot levers. Squeezing the cups together pulls the closing linkage, and a release tab frees the linkage so a return spring opens the grip.
A pinion drives a toothed rack linked to the fingers, and a ratchet wheel shares the pinion shaft. A spring-loaded pawl rides over the wheel teeth during closure and engages a tooth under reverse load. A release lever lifts the pawl to permit opening.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Within the retractor body 140 is a cord spool 145 which may be locked into a chosen position, corresponding to a desired overall strap length. The cord spool 145 may have teeth on its top edge adapted to receive a portion of the lock 143 to implement a stoppage of the rotation of the cord spool 145.B · US 2014/0093230 A1 · ¶ 32
In the embodiment illustrated, fasteners, also referred to as retainer members 48, are used to fasten the drape 46 against the outer surfaces 42 of the clips 24. The retainer members 48, by way of example and without limitation, are shown as being generally L-shaped, having a first portion 50 configured to overlie and fasten to the respective leg 30, 32, and a second portion 52 configured to overlie and fasten to the extension 43.A · US 2013/0025605 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
In addition, having to stock and/or order a specific size drape clip, depending on the size of the C-arm, can increase inventory requirements and costs associated therewith.A · US 2013/0025605 A1 · ¶ 7
A drape clip constructed in accordance with the invention at least overcomes those disadvantages of known drape clips discussed above, as well as others disadvantages, as will be apparent to one possessing ordinary skill in the art upon viewing the disclosure herein.A · US 2013/0025605 A1 · ¶ 8
What is called for is a device which may function as a wrist strap, and also extend out to be a neck strap, for the support of a camera.B · US 2014/0093230 A1 · ¶ 6
The present invention is directed towards a versatile retractable strap assembly adapted to mount to the bottom of a camera, or other device, and to be used in a variety of configurations.B · US 2014/0093230 A1 · ¶ 7
patent.fyi, US 2026/0354810 A1, claim 1, first published 2026-11-19T04:13:02-05:00, https://patent.fyi/US20260354810/, SHA-256 40433d580ce29fdd0bef15e63888e0df26f23652abd4d0d0080391b0ca2cd6de