1.2Bipolar compression seal
Opposing electrode plates deliver radio-frequency current through the compressed tissue. Pressure and resistive heating fuse the tissue layers along the electrode face.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Opposing electrode plates deliver radio-frequency current through the compressed tissue. Pressure and resistive heating fuse the tissue layers along the electrode face.
A curved needle passes suture through both tissue layers at successive sites along the first line. Each strand is tied separately to hold the layers together at its stitch site.
A pair of anvil pockets directs one leg to each side of the crown plane. Each pocket also curls its leg back toward the crown to capture the tissue.
The second-row anvil pockets lie in the plane defined by the crown and the unformed legs. Curved pocket floors turn both leg tips back toward the crown within that plane.
An applicator spreads each clip and places its arms over opposite faces of the tissue edge. On release, spring force draws the arms together and compresses the tissue between them.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Opposed jaws clamp the overlapping edges of an industrial felt filter sleeve. A cartridge holds three longitudinal rows of staples, and the opposing jaw carries a forming pocket for each leg. The driver pushes the staples through both layers, and the pockets form one row with the legs in the crown plane and two rows with different lateral leg angles.
Staples made of commercially pure titanium wire replace stainless steel wire staples in the three cartridge rows. Each staple retains a straight crown and two legs, and the cartridge slots support the legs until they enter the tissue. Radiused anvil grooves guide the legs into the three row-specific shapes, with groove exit angles set to account for springback after the jaws open.
A traveling carriage with three cam rollers replaces the sliding wedge that lifts the staple pushers. Each roller runs beneath one longitudinal row and lifts successive pushers by contacting ramps on their undersides. Guide rails constrain carriage motion, and each pusher drives its staple toward matching anvil pockets that form the legs at the angle assigned to that row.
A 30 mm cartridge carries three longitudinal rows of eight staples, with a 3 mm center-to-center pitch within each row. The middle row is shifted 1.5 mm along the cartridge relative to the outer rows, and its anvil pockets follow the same offset. The pockets form legs at lateral angles of 0, 10, and 20 degrees relative to the crown plane in the first, second, and third rows, respectively.
An articulated robotic surgical arm carries the two-jaw stapling head on a detachable shaft. Separate motor couplings in the shaft close the jaws and advance a firing sled through the cartridge. The sled lifts the staple pushers as it travels, while the fixed anvil pockets determine the lateral leg angle in each row.
Two displacement sensors measure the closed-jaw gap near the proximal and distal ends of the cartridge. A controller samples both sensors during closure and enables the firing motor when both gaps remain within the cartridge's stored compression band for a preset dwell time. A motor encoder tracks sled travel to the end of the cartridge, and the anvil pockets form the three row-specific leg angles during the stroke.
A central draw rod pulls the anvil disk axially toward the cartridge face. The opposing annular surfaces compress the tissue around the rod before firing.
A sliding sleeve rides over a cam surface on the pivoting jaw and closes it against a fixed cartridge jaw. A mechanical stop sets the minimum gap between the closed jaw faces.
A cartridge driver advances a U-shaped titanium staple into two curved anvil pockets. Both pockets lie in the crown plane and curl the legs inward within that plane.
Two oblique pockets in the second-row anvil surface guide the legs to opposite sides of the crown plane as they curl. The pockets have matching lateral inclinations and produce equal angular departures from the crown plane.
The third-row anvil pockets have a steeper lateral inclination than the second-row pockets. Their forming surfaces curl both legs back toward the crown and give each leg a greater lateral angle relative to its crown plane.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Tissue to be stapled can then be grasped by the jaws. The jaws can optionally squeeze the tissue for a period of time to induce “milking” of the tissue.A · US 2007/0114261 A1 · ¶ 39
Surgical staplers, as outlined above, can be configured to pivot the anvil of the end effector relative to the staple cartridge in order to capture soft tissue therebetween. In various circumstances, the anvil can be configured to apply a clamping force to the soft tissue in order to hold the soft tissue tightly between the anvil and the staple cartridge.B · US 11,013,511 B2 · ¶ 4
An empty cell means only that no passage was reproduced there.
Such repeated removal and insertion is time consuming and also increases the possibility of surgical complications.A · US 2007/0114261 A1 · ¶ 4
The present invention generally provides methods and devices for forming a pattern of staples that conform to a selected shape of a surgical stapler end effector.A · US 2007/0114261 A1 · ¶ 6
As known in the art, surgical staplers are often used to deploy staples into soft tissue in order to reduce or eliminate bleeding from the soft tissue, especially as the tissue is being transected, for example.B · US 11,013,511 B2 · ¶ 3
As a result, when the end effector is articulated, the end effector may apply a shear force to the soft tissue captured between the jaw members.B · US 11,013,511 B2 · ¶ 3
patent.fyi, US 2026/0354818 A1, claim 1, first published 2026-11-19T04:13:02-05:00, https://patent.fyi/US20260354818/, SHA-256 7f8fb65dfbe2bdb33cace133d580307dfefa69370f3dec77d62f6f2e62049efb