1.2Buck charging from series cells
Four series lithium-ion cells feed a synchronous buck regulator that charges a balanced supercapacitor bank to 10 V. A current-sense resistor and feedback loop limit charging current to 0.5 A.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Four series lithium-ion cells feed a synchronous buck regulator that charges a balanced supercapacitor bank to 10 V. A current-sense resistor and feedback loop limit charging current to 0.5 A.
The dock supplies 5 V to a boost converter that charges the supercapacitor bank to 12 V. The onboard cells supply a separate logic rail, and the charged bank supplies the motor after undocking.
The boost circuit feeds a constant-current, constant-voltage charger for a four-cell lithium iron phosphate pack. The pack has cell-voltage monitoring and supplies the motor pulse through a low-resistance output path.
The module output remains wired to the motor driver throughout charging. The driver applies a low input current limit at low supercapacitor voltage and increases that limit as the stored voltage rises.
A break-before-make rotary switch connects the supercapacitor to the charging circuit in its charge position. When the voltage indicator reaches the marked ready level, the operator turns the selector to run, which connects the bank to the motor supply.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handheld label cutter contains a battery compartment, a boost converter, and a supercapacitor connected across the converter output. A normally open relay sits between the supercapacitor and the cutter solenoid driver. Pressing the cut button starts a charge cycle and holds the relay open for a fixed interval, after which the relay closes and the driver pulses the solenoid.
A regulated switched capacitor voltage doubler replaces the inductor-based boost converter. The doubler charges a flying capacitor across the battery and then stacks the flying capacitor in series with the battery to transfer charge to the supercapacitor. A hardware timer holds the load switch open during a charge interval sized for the minimum battery voltage, maximum reservoir capacitance, and minimum available charging current.
Six 25 F, 2.7 V supercapacitor cells form a series bank with a nominal capacitance of 4.17 F. A boost converter raises the voltage from four 1.2 V battery cells, limits bank charging current to 0.5 A, and regulates the bank at 14.4 V. A balancing circuit monitors each cell and suspends charging if any cell reaches 2.6 V. A 180 s timer holds the load contactor open after charger enable, and the output interlock keeps it open if the charger reports a fault.
The battery compartment feeds a boost converter that charges a supercapacitor bank, and a delayed load switch connects the bank to the motor bridge of a force controlled stapler. The charger asserts a ready signal to the stapler controller after the timed charge interval and load switch closure. During firing, the controller reads a strain gauge on the drive linkage and an encoder on the motor, then adjusts motor current to regulate linkage force as the mechanism travels.
A microcontroller powered from the battery monitors the supercapacitor bank while the boost converter charges it and the instrument load switch remains open. At timed intervals, the controller pauses the converter and pulses a known resistor across the bank through a test transistor. It estimates series resistance from the immediate voltage drop and capacitance from the subsequent voltage slope. The controller closes the load switch when the measured bank voltage and estimated parameters predict that the specified instrument current pulse stays above the load's minimum operating voltage.
A programmable boost converter connects the battery compartment to a supercapacitor bank, and a microcontroller measures battery terminal voltage and input current during charging. The controller samples the battery voltage before charging, ramps the input current command, and reduces the command when the voltage drops below a configured floor. The controller keeps the instrument output switch open while accumulated charge, measured through a shunt in the bank charging path, is below the programmed target. It sets that target from the bank voltage measured at the start of the cycle and the configured bank capacitance.
The battery cells remain in a separate enclosure connected to the power module by a flexible cable. A sealed bulkhead connector carries the battery supply to the charging circuit.
A molded polymer tray holds two cylindrical cells side by side. Nickel-plated spring contacts connect the cells in series, and a hinged cover retains them against the contacts.
An inductor and two switching transistors raise a 3.6 V battery supply to a regulated 12 V charging output. A current-sense resistor limits battery input current as the storage voltage rises.
Five 2.7 V, 25 F supercapacitor cells connected in series provide a nominal bank capacitance of 5 F. Active shunt circuits limit individual cell voltages during charging to a bank voltage of 12 V.
A voltage comparator monitors the supercapacitor through a resistor divider. At 11.5 V, it enables a gate driver that turns on back-to-back transistors and connects the module output to the motor driver.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The battery receptacle has a battery compartment delimited by a first stop and a second stop, situated opposite the first stop, for holding a first buffer battery between the first stop and the second stop.B · US 2014/0016251 A1 · abstract
No. 6,265,851 describes an electric vehicle power system for a semiconductor wafer handling application, having ultracapacitors and batteries as parallel sources connected to a source-selecting switch and having said switch direct its output only to a DC-DC converter which serves the motor load, however, this incurs the converter losses when no conversion is necessary.A · US 7,642,755 B2 · ¶ 5
A delay corresponding to the known response time of the DC-DC converter 24 ensures that opening of Contactor 21 connection to the output bus lines 6 does not cause momentary sagging of the ESS output voltage (alternative control designs may equivalently serve to ensure smooth operation of the ESS output bus during switching).A · US 7,642,755 B2 · ¶ 23
An empty cell means only that no passage was reproduced there.
The present invention relates to an apparatus and method to extract a larger portion of the available energy capacity of “Ultra-Capacitor” (or “Super-Capacitor”) energy storage systems (ESS).A · US 7,642,755 B2 · ¶ 1
In order to fully-extract the energy from an Ultra-Capacitor System (UCS), they must undergo a large voltage decrease, causing system output voltage issues.A · US 7,642,755 B2 · ¶ 3
It is an object of one embodiment of the invention to provide a vehicle data recording unit of the type specified in the introduction that can use buffer batteries of different physical size.B · US 2014/0016251 A1 · ¶ 5
A particular advantage of one embodiment of the invention is that, despite only one battery compartment being provided, it is nevertheless optionally possible, in a space-saving manner, for buffer batteries of different dimensions to be securely held.B · US 2014/0016251 A1 · ¶ 7
patent.fyi, US 2026/0354823 A1, claim 1, first published 2026-11-19T04:13:02-05:00, https://patent.fyi/US20260354823/, SHA-256 e7d9c92394ed9b7735d094024d221c38a2739028d9911665e00c3a3cf3a501d4