1.1Open guidewire saddles
Two axially spaced polymer saddles capture the guidewire between flexible lips. The lips leave a longitudinal slit in each saddle, and the guidewire slides axially through the saddles as the catheter advances.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two axially spaced polymer saddles capture the guidewire between flexible lips. The lips leave a longitudinal slit in each saddle, and the guidewire slides axially through the saddles as the catheter advances.
Thin polymer pads bonded to the inner balloon wall carry the emitter modules and spread their loads over the balloon film. Flexible leads connect the modules to conductors in the proximal catheter wall, and an exterior guidewire track guides the assembly.
A single electrode pair generates pressure pulses in the balloon fluid at each treatment position. The operator deflates the balloon, shifts the catheter along the guidewire, and reinflates it before pulsing at the next position.
A voltage burst applied to the metallized faces of each piezoelectric element produces rapid ceramic strain. The vibrating faces launch pressure pulses into the balloon fluid, which transmits them through the balloon wall.
A conductive disk presents a flat annular face, and a separate electrode tip faces that surface across an axial fluid gap. A voltage pulse initiates a discharge across the gap and generates a pressure wave in the balloon fluid.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A guidewire runs through a small-bore heat exchanger tube in an isolated maintenance circuit. A catheter tracks over the wire and carries four spark-gap emitters along an inner shaft inside a liquid-filled balloon. The inflated balloon contacts the tube wall, and sequential discharges transmit pressure pulses through the balloon to fracture mineral deposits. A flush through the tube carries loosened debris to a downstream strainer after balloon deflation.
An alumina capillary replaces the dielectric jacket on the conductor segment within each emitter module. The capillary seats in an insulating carrier beside the conductive emitter body and ends before the exposed conductor tip. The carrier positions the tip across a liquid-filled spark gap from the emitter body surface. Flexible insulated leads run along the inner shaft outside the guidewire lumen and connect to the sleeved conductor segments.
Five emitter modules sit at 4 mm center-to-center spacing along a shaft inside a balloon with a 24 mm working length. The middle module aligns with the axial midpoint of the working length. The shaft lumen accepts a 0.045-inch (1.143 mm) guidewire, and emitter leads run in the shaft wall. Separate switched channels fire the modules in order from the distal end toward the proximal end.
A circumferential intravascular ultrasound array mounts on the catheter immediately distal to the balloon, around a guidewire lumen that continues through the distal tip. Array wiring runs separately from the discharge conductors to an imaging console. During a pullback pass with the balloon deflated, the console records cross-sectional images and their axial positions. The operator uses the recorded positions and the fixed array-to-balloon offset to place the emitter array over the imaged segment.
Each emitter connects to an individually switched output of a pulse generator. A voltage divider and a current transformer at the generator output feed a digitizer that records the waveform for each firing command. Software checks for the voltage collapse and current rise associated with gap breakdown and records the result against the selected emitter. After two consecutive commands without detected breakdown, the controller removes that channel from the firing sequence and flags its axial position on the display.
A pressure transducer connects to the balloon inflation lumen at the proximal manifold, where a holding valve isolates the filled balloon and transducer from the pump. The controller enables a firing sequence after the measured pressure stays within a configured band for a specified settling time. The controller excludes the brief discharge transient from its baseline estimate and checks the recovered pressure before enabling each subsequent pulse. A sustained pressure excursion disables the generator output and leaves the inflation circuit available for operator-controlled deflation.
An alumina carrier positions two electrically independent metal pins with their exposed tips facing across a fluid gap. A voltage pulse drives a discharge between the tips, and the alumina carrier provides mechanical support for both pins.
A polytetrafluoroethylene liner forms a continuous guidewire lumen with a 0.040-inch inner diameter for a 0.035-inch guidewire. A polyamide jacket supports the liner and preserves its circular bore during bending.
A polyamide inner shaft contains a central guidewire bore and two enclosed longitudinal conductor channels in its wall. The channels carry insulated leads to local openings at the emitter attachment sites.
Four stainless steel collars mount at 4 mm center-to-center spacing along the inner shaft within the balloon. Each collar presents a cylindrical electrode surface, and an exposed wire tip faces that surface across a radial spark gap.
A polyimide sleeve covers the part of the conductor that runs alongside the metal emitter body. A local opening in the sleeve exposes a short conductor segment facing the body across a fluid-filled spark gap.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A catheter placement system, comprising: a needle supported by a needle hub and defining a needle lumen; a guidewire having a distal tip disposed within the needle lumen; a catheter disposed on a proximal portion of the guidewire; and a guidewire locking system, comprising: a housing defining a needle channel and a guidewire channel communicating with the needle channel and extending at an angle thereto, a portion of the needle extending through the needle channel and a portiA · US 2023/0129318 A1 · claim 1
In some examples, the handle 22 is configured to receive a guidewire through a guidewire lumen in the elongated tube 12 to aid in insertion and positioning of the distal end 14 of the catheter 100.B · US 2025/0064470 A1 · ¶ 181
In a particular embodiment, the elongate member 242 includes an inner shaft and an outer shaft concentric with and at least partially surrounding the inner shaft.B · US 2025/0064470 A1 · ¶ 214
Each of the emitters may include at least one electrode pair, with the electrodes of each pair spaced apart from one another to form a spark gap between the electrodes across which shock waves can be generated.B · US 2025/0064470 A1 · ¶ 226
An empty cell means only that no passage was reproduced there.
However, as the guidewire passes through the needle slot, forces acting on the guidewire can dislodge the position of the distal tip within the vasculature.A · US 2023/0129318 A1 · ¶ 3
In some embodiments, the seal is formed of a compliant material and defines a seal guidewire lumen configured to receive a portion of the guidewire therethrough, the lock in the locked position configured to compress the seal radially inwards to impinge on the guidewire and inhibit axial movement thereof.A · US 2023/0129318 A1 · ¶ 5
Alternative devices to deliver IVL therapy can be within a closed volume other than an angioplasty balloon, such as a cap, balloons of variable compliancy, or other enclosures.B · US 2025/0064470 A1 · ¶ 7
However, conventional shock wave catheters may be less effective for treating lesions in large blood vessels and valves.B · US 2025/0064470 A1 · ¶ 8
patent.fyi, US 2026/0354852 A1, claim 1, first published 2026-11-19T04:53:05-05:00, https://patent.fyi/US20260354852/, SHA-256 6f598ce64fc8362f08720e7ff0c72c932ab9fdc8fc9e7e0cccda8ad30c9aecfa