1.1Open saddles for pin shafts
Each shaft enters its V-saddle from the side. A screw-driven shoe presses the shaft against the two saddle faces, and the resulting friction transfers load between the link and the shaft.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each shaft enters its V-saddle from the side. A screw-driven shoe presses the shaft against the two saddle faces, and the resulting friction transfers load between the link and the shaft.
The mount slides over the exposed pin end until the tip reaches the pocket floor. A radial clamp screw presses the shaft against the pocket wall so the mount transfers load to the pin.
A hand pump supplies pressure to a cylinder fixed to the guide. The piston drives the pin carriage toward a fixed pin mount, and a shutoff valve retains pressure between adjustments.
Each pin is secured by a set screw in a rigid mount with coaxial holes. A handwheel drives the pinion against a rack on the sliding mount and changes the distance between the two pins.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A reusable spring link spans a seam between two panels on a fabrication fixture. Temporary studs thread into inserts on opposite sides of the seam, and a loading jig holds the upper and lower holes of each pair in alignment while the studs pass through them. When the jig releases the link, the hole pairs shift in opposite directions and press against the studs to draw the panel edges together.
Two rigid plates with transverse holes pivot about a shared axis and are biased apart in rotation by a helical torsion spring. A removable loading lever rotates the plates until each upper hole aligns with its lower hole, allowing the percutaneous fasteners to pass through both plates. Removing the lever lets the spring rotate the plates toward their rest angle, so the opposing hole walls bear against each fastener at two heights.
Press-fit flanged bushings replace the direct contact surfaces of the upper and lower holes, with each flange seated against the outer face of its plate. The bushing bores share an axis when the loading fixture holds the link open, allowing a fastener to pass through both bushings. When the fixture releases the link, the bores shift relative to each other and their opposing walls transfer load to the fastener shank.
A bench fixture mounts two 4 mm dummy pins 60 mm apart on separate sliding blocks. A loading jig aligns both hole pairs on the pins, and interchangeable stop shims limit the returning plate to 0.25 mm, 0.50 mm, or 1.00 mm of travel at a reference face. A dial indicator on each block records displacement after release, and a compression load cell between the blocks records the transmitted force.
A linear external fixation rail carries two sliding carriages, each with a fastener clamp and a separate percutaneous fastener. One additional fastener on each segment projects through an aligned hole pair in the spring link, which spans the carriages parallel to the rail. As the link returns toward its rest shape, it loads the projecting fasteners while the carriages guide the segments along the rail.
A strain gauge bridge bonded to the flexing portion of the link measures bending, and a displacement sensor measures relative motion between the upper and lower hole plates. A motorized loading screw holds the hole pairs aligned during fastener insertion and retracts in discrete steps to let the link return toward its rest shape. A controller pauses at each step, records plate displacement, and converts the bridge reading to bending moment using a calibration curve from known bench loads.
Each socket seats on a matching tapered pin head. A draw screw pulls the head against the socket, and the seated taper transfers transverse load and bending moment.
A fixed pin mount and a sliding pin mount attach to the exposed pin ends while the lead screw is unloaded. Turning the screw draws the sliding mount toward the fixed mount along a guide rail and compresses the attached bone segments.
A stainless steel link has two transverse hole pairs spaced along its length. Each pair consists of one circular bore through an upper leaf and one through a lower leaf.
Two spring steel leaves join at one end and have different formed curvatures. In the unloaded configuration, the curvature difference offsets the upper and lower hole centers along the length of the link.
A removable toggle fixture deflects the leaves against a machined stop that brings each upper bore into alignment with its lower bore. A bone pin passes through each aligned pair while the fixture holds the leaves at the stop.
Releasing the fixture lets the leaves spring back until opposed bore edges contact each pin at two heights above the skin. The contact forces apply a bending moment and a net transverse force to each pin, with the forces directed to draw the attached bone segments together.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The expression member is configured to repeatedly move from a relaxed position over the incision to a contracted position over the incision.A · US 9,332,931 B2 · abstract
As shown in FIG. 2, preloading element 26 is formed by bending tab 34 away from interior 30 of drive plate 14 so that the bent tab 34 contacts and presses against outer surface 54 of first portion 40 of front cover 16 with free end 36 of tab 34 when drive plate 14 is fixed to front cover 16.B · US 10,274,064 B2 · ¶ 18
As shown in FIG. 2, preloading element 26 is formed by bending tab 34 away from interior 30 of drive plate 14 so that the bent tab 34 contacts and presses against outer surface 54 of first portion 40 of front cover 16 with free end 36 of tab 34 when drive plate 14 is fixed to front cover 16. Tab 34 is compressed by the connection between drive plate 14 and front cover 16 and is urging front cover 16 away from drive plate 14.B · US 10,274,064 B2 · ¶ 18
FIGS. 8 and 13 also illustrate the relative positions of the expression member 130, the compression member 132, and the housing 160 after the compression member 132 has been rotated such that the compression lobes 150 traverse the expression nubs 144 and the compression lobes 150 are no longer contacting the expression nubs 144. In FIG. 8, the fingers 148 and the passageway 146 contract to a relaxed position.A · US 9,332,931 B2 · ¶ 49
An empty cell means only that no passage was reproduced there.
Varying the pressure and pulsating the skin surrounding the incision increases the amount of bodily fluid expressed to the incision.A · US 9,332,931 B2 · ¶ 7
Therefore, it is important to express an adequate sample of body fluid required for testing at an alternate site.A · US 9,332,931 B2 · ¶ 8
The cover assembly includes a front cover and a drive plate connected to an outer surface of the front cover for coupling to the front cover to an engine crankshaft.B · US 10,274,064 B2 · ¶ 4
The elastic preloading elements may be formed by tabs formed into the interior of the drive plate and bent toward the front cover.B · US 10,274,064 B2 · ¶ 6
patent.fyi, US 2026/0354867 A1, claim 1, first published 2026-11-19T04:53:05-05:00, https://patent.fyi/US20260354867/, SHA-256 550c0ae75b33db6fe91c58f4f7a33406992b26d872ff93443f8add7b777c0d3e